background image

GCS522014  Sportsman 20-Inch + 14-Inch Chainsaw Instruction Manual            

                                                  16  

 

 

 
 

EMISSIONS CONTROL WARRANTY STATEMENT 

 

YOUR WARRANTY RIGHTS AND OBLIGATIONS 

United Sates Environmental Protection Agency (EPA), and Buffalo Corp are pleased to explain the emissions control 
system warranty on your 2020 small off road engine (SORE). Buffalo Corp must warrant the emissions control system on 
your SOREs for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of 
your SOREs. Your emission control system may include parts such as the carburetor, fuel tanks, fuel caps, fuel lines, the 
ignition system, and catalytic converter. Also included may be hoses, belts, clamps, connectors and other emission related 
assemblies. Where a warrantable condition exists, Buffalo Corp. will repair your small off-road engine at no cost to you 
including diagnosis, parts and labor. 

 
MANUFACTURER’S WARRANTY COVERAGE: 

The emissions control system is warranted for two years. If any emissions related part on your engine is defective, the part 
will be repaired or replaced by Buffalo Corp. 
 

OWNER’S WARRANTY RESPONSIBILITIES: 

As the SORE owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. 
Buffalo Corp. recommends that you retain all receipts covering maintenance on your SORE, but Buffalo Corp. can not 
deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. 
As the SORE owner, you should however be aware that Buffalo Corp. may deny your warranty coverage if your SORE or 
a part has failed due to abuse, neglect, improper maintenance or unapproved modifications. 
You are responsible for presenting your SORE to distribution center or service center authorized by Buffalo Corp. as soon 
as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. 
If you have any questions regarding your warranty coverage, you should contact Buffalo Corp. customer service 
representative at: 
Tell :

 

1-866-460-9436 

Email :

 

info@buffalotools.com  

 

DEFECTS WARRANTY COVERAGE 

Adopted by the Air Resources Board, Buffalo Corp. warrants to the ultimate purchaser and each subsequent purchaser that 
the small off-road engine (SORE) (1) has been designed, built and equipped so as to conform with all applicable 
regulations; and (2) is free from defects in materials and workmanship that cause the failure of a warranted part to 
conform with those regulations as may be applicable to the terms and conditions stated below. 
(A) The warranty period begins on the date the engine is delivered to an ultimate purchaser. The warranty period is two 
years. 
(B) Subject to certain conditions and exclusions as stated below, the warranty on emissions related parts is as follows: 
(1) Any warranted part that is not scheduled for replacement as required maintenance in your Owner’s Manual is 
warranted for the warranty period stated above. If the part fails during the period of warranty coverage, the part will be 
repaired or replaced by Buffalo Corp. according to Subsection (4) below. Any such part repaired or replaced under 
warranty will be warranted for the remainder of the period. 
(2) Any warranted part that is scheduled only for regular inspection in your Owner’s Manual is warranted for the warranty 
period stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty 
period. 
(3) Any warranted part that is scheduled for replacement as required maintenance in your Owner’s Manual is warranted 
for the period of time before the first scheduled replacement date for that part. If the part fails before the first scheduled 
replacement, the part will be repaired or replaced by Buffalo Corp., according to Subsection (4) below. Any such part 
repaired or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled 
replacement point for the part. 
(4) Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty 
station at no charge to the owner. 
(5) Notwithstanding the provisions herein, warranty services or repair will be provided at all of our distribution centers 
that are franchised to service the subject engines. 

Summary of Contents for GCS522014





















Reviews: