background image

 

 

 

 

7.

 

DO NOT

 use a GunJet with a faulty or damaged Trigger Lock.

 

8.

 

DO NOT

 operate a spray gun if there are any leaks from the packings, 

fittings, hoses, etc. Fluids that are under high pressure can penetrate 

skin, cloth, etc., and cause serious injury. 

9.

 

DO NOT

 touch any metal parts of the gun or accessories when 

spraying hot liquids or severe injury can occur. 

10.

 

DO NOT

 handle a spray gun without

 

a tip or nozzle any differently 

than one with

 

a tip or nozzle. Even with the tip or nozzle removed, the 

spray gun can discharge a large volume of liquid at a high velocity. 

SAFETY SHOULD ALWAYS BE OBSERVED 

1.

 

DO 

use a two-handed control of Model 60 GunJet at all times. Grasp 

spray gun firmly with both hands. If an extension is used, grasp the 

extension. (Insulated extension if spraying hot liquids.) 

2.

 

DO 

adopt a secure body stance prior to and during spray operation to 

safely control the high reactionary force of this unit. 

3.

 

DO

 impress on other people in the spraying area the importance of 

obeying strict safety precautions for everyone’s safety. 

4.

 

DO

 develop a habit of shutting off the power to the pump, relieving 

fluid pressure from gun and hose by actuating trigger until all fluid 

ceases to flow, and setting the Trigger Lock in the locked position, 

before attempting to remove the tip, nozzle, gun or any part of the 

gun, or when gun is not in use. 

5.

 

DO 

check operation of Trigger Lock before each spray period. Trigger 

Lock must hold the Trigger to its forward position. (Adjust if necessary; 

s

ee section Trigger Adjustment Procedure.) 

6.

 

DO

 carefully check and tighten threaded connections regularly. Make 

them secure and leak proof. 

7.

 

DO

 flush gun after each spray period using the same safety 

precautions as used during spraying operations. Always use the lowest 

possible pressure for flushing. 

8.

 

DO

 keep gun clean and dry to allow for positive grip. 

9.

 

DO

 use GunJet in a well-ventilated area and make sure spray gun is 

grounded properly when used in a possibly explosive or inflammable 

environment. A grounded-type hose should be used. 

IMPORTANT: In case of the slightest appearance of skin penetration from 

spray, CONSULT A PHYSICIAN IMMEDIATELY! 

Summary of Contents for GunJet 30A













Reviews: