background image

iii

020-053-UK R2

BoomPilot

®

Table of Contents

Matrix prO® with tJ744E sprayEr COntrOl 

iv

intrOduCtiOn tO tJ744E - aBsC 

1

principle of Operation ............................................................................. 1
required parts ......................................................................................... 1

installing thE tJ744 aBsC kit 

3

Connecting to power ............................................................................... 3

Battery Cable (Option) .....................................................................................3

Mount & Connect sdM ............................................................................ 4
power/Can/data Cable to Boompilot harness ..................................... 4

systEM ChECk 

5

Check AUTO mode: ..........................................................................................5

TJ744E Switch box: ......................................................................................5

Matrix Pro: ....................................................................................................5

Check MANUAL mode: .....................................................................................5

TJ744E Switch Box: .....................................................................................5

Matrix Pro: ....................................................................................................5

COnfiguratiOn using yOur Matrix

®

 prO 

6

vehicle setup ........................................................................................... 7
implement - smartCable or sdM ............................................................ 8

OpEratiOn using yOur Matrix

®

 prO 

9

Off/Manual & Automatic  ..................................................................................9

All Booms On Mode .........................................................................................9

Example......................................................................................................10

BoomPilot Status ............................................................................................10

Summary of Contents for TeeJet TECHNOLOGIES BoomPilot

















Reviews: