background image

 

 

 

CONTENTS 

INTRODUCTION .......................................................................................... 2

 

WARNINGS & PRECAUTIONS ...................................................................... 3

 

INSTALLATION ............................................................................................ 5

 

MAINTENANCE ........................................................................................... 6

 

PARTS LIST .................................................................................................. 8

 

 

INTRODUCTION  

The Model PW4000A- GunJet is a high-pressure spray gun that offers exceptional 

operator control, even at maximum flow and pressure conditions. A bottom pivot 

trigger reduces operator fatigue by making trigger pull easier. The shut-off valve is 

located in the base of the handle, concentrating heat away from the operator’s hand 

and slowing heat build-up. A special trigger lock feature locks in the “off” position to 

prevent accidental discharge and retracts flush into the handle when the gun is in use. 

The Model PW4000AW- incorporates a continuous “Weep” feature to minimize the 

chance of freezing and, with the exception of the valve seat sub-assembly, the 

PW4000A- and PW4000AW- GunJet spray guns are identical and require the same 

installation and operating procedures. The Model PW4000A- and PW4000AW- 

GunJet spray guns with the “S” option have a built-in swivel to reduce operator 

fatigue and prolong hose life. 

FEATURES OF THE MODEL PW4000A - GUNJET SPRAY GUNS:  

 

Operating pressure range — up to 4000 psi (275 bar). 

 

Maximum recommended temperature — 300° F (150° C). 

 

Forged Brass Inlet Body. 

 

Stainless Steel shut-off. 

 

TEFLON

®

 Back-Up Rings.* 

 

Viton

®

 O-rings.* 

 

Handle design helps to control reactionary force during trigger actuation. 

 

Teflon is a registered trademark of DuPont Company 

* Viton is a registered trademark of DuPont Performance Elastomers 

Summary of Contents for GunJet PW4000A













Reviews: