background image

17

Preparation

turned on or off, the line indicator flashes
when a call is received. The phone is preset
as ringer ON for all lines.

To turn the ringer off for individual lines, fol-
low these steps.

1. Press 

PROGRAM

.

2. Select 

PHON

, then select 

NEXT

 twice so

the 

RINGER

 

SELECT

 menu appears. 

3. Select 

ENTER

LINE

 

n

 

RING: ON

appears.

4. Select 

CHANGE

 to toggle between turn-

ing the ringer 

ON

 or 

OFF

 for the selected

line.

5. Select 

NEXT

 to advance to the next line

selection.

6. Repeat Steps 4 and 5 until all lines are

programmed.

7. Press 

PROGRAM

 to exit.

Setting the Ringer Volume

You can set the ringer volume to 

HI

LOW

, or

OFF

, using 

RINGER

 

VOL

When set to 

OFF

, the phone does not ring

when a call is received on any lines. 

Setting Always Ring

Your system is designed so your phone does
not ring when there is an incoming call on
one line if you are already talking on another

line, or when the Auto Attendant feature is
on. 

However, you can set your station to Always
Ring (even in these circumstances).

Note: Even with Always Ring on, the station
does not ring when you are talking on the
speakerphone (outside line or intercom).

1. Press 

PROGRAM

.

2. Select 

PHON

.

3. Select 

NEXT

 four times so 

ALWAY-

SRING

 appears.

4. Select 

CHANGE

 to toggle between 

ON

and 

OFF

.

5. Press 

PROGRAM

 to exit.

SETTING THE HANDSET, 
HEADSET AND SPEAKER 
VOLUME

You can individually set the volume levels for
the handset, speaker, and headset. When
you switch over, the volume level is automat-
ically changed to the set level.

Handset/Headset Volume

While using the handset or headset, select 

 to adjust the volume. One to four

bars appear to show the volume level. (1 bar
is the lowest and 4 bars is the highest.) The
volume setting remains at this level until you
change it or a power failure occurs. 

Speakerphone Volume

When using the speakerphone or when the
phone is not in use, select 

– 

 to set

the speakerphone volume. One to eight sets
of bars appear to show the level. The volume
setting remains at this level until you change
it or a power failure occurs. 

OFF/LO/HI
RING VOL.

43-5708.fm  Page 17  Monday, September 18, 2000  7:56 AM

Summary of Contents for SP708









































Reviews: