background image

SPRT 

 

 

 
Introduction 

 
 

POS58

printer is a new type line thermal printer ,it features in fast 

speed printing, low 

printing  noise,  high  reliability,  perfect  printing  quality  and

  ribbon  needless  avoiding  the 

vexation of regular maintenance. 

 

POS5

8Ⅳ

  printer:  small  in  outline  dimension,  simple  operation,  and  extensive  application, 

especially  suitable  for  commercial  cash  register, 

PC-POS,  bank  POS  and  all  kinds  of 

receipts printing.

 

Chapter 1 Characteristic Specification

 

 

1.1Printing Specification

 

 

Printing method: direct thermal

 

Printing paper width:57.5±0.5mm

 

Printing density:8dots/mm,384dots/line

 

Printing speed:approx.60mm

sec.

 

Reliability:

 

Printing head life:100km

 

Using condition: 

Print 12 × 24 ASCII characters, print 50 lines each time,

 

intermittent print repeatedly

 

Each dot-line printing at the same time should not exceed 25%,

 

each character-line and 

one dot vertically printing repeatedly

 

should not exceed11 times

 

Use specified thermal paper

 

Valid printing width:48mm

 

1.2

 Printing Paper

 

Thermal paper model:TF50KS

E

Japan paper co. ltd

 

AF50KS-E(JUJO THERMAL) 

Summary of Contents for SP-POS5IV

































Reviews: