background image

 

 

 

WARNING

 

FOLLOW THESE BASIC PRECAUTIONS TO 
REDUCE THE RISK OF FIRE, ELECTRICAL 
SHOCK, OR INJURY WHEN USING YOUR ICE 
MAKER. 

 

• 

READ ALL INSTRUCTIONS BEFORE USING THE ICE MAKER. 

• 

DANGER:  RISK OF CHILD ENTRAPMENT. 

      CHILD ENTRAPMENT AND SUFFOCATION ARE NOT PROBLEMS OF THE PAST.  

JUNKED OR ABANDONED APPLIANCES ARE STILL DANGEROUS. 

• 

BEFORE YOU THROW AWAY YOUR ICE MAKER: TAKE OFF THE DOOR. 

• 

NEVER ALLOW CHILDREN TO OPERATE, PLAY WITH, OR CRAWL INSIDE THE 
APPLIANCE. 

• 

NEVER CLEAN ICE MAKER PARTS WITH FLAMMABLE FLUIDS.  THE FUMES CAN 
CREATE A FIRE HAZARD OR EXPLOSION. 

• 

DO NOT STORE OR USE GASOLINE OR ANY OTHER FLAMMABLE VAPORS AND 
LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.  THE FUMES CAN 
CREATE A FIRE HAZARD OR EXPLOSION. 

 

 

IMPORTANT SAFETY INSTRUCTIONS 

 

WARNING: To reduce the risk of fire, electric shock or injury when using your icemaker, 
follow these basic precautions: 

• 

Disconnect power before cleaning. 

• 

Replace all panels before operating. 

• 

Do not use an extension cord. 

• 

Disconnect power before servicing. 

• 

Do not use an adapter. 

• 

Have two or more people to move/install the icemaker.] 

 
 

 

ELECTRICAL CONNECTION 

 

 
 
 
 
 

• 

This  icemaker should be properly  grounded for  your  safety.    The  power  cord of this icemaker  is 
equipped with a three-prong plug which mates with standard three prong wall outlets to minimize 
the possibility of electrical shock. 

• 

DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUNDING PRONG 
FROM THE SUPPLIED POWER CORD. 

• 

Do not use an adapter and do not use an extension cord. 

• 

If you only have a two-prong wall receptacle, contact a qualified electrician to have it replaced with 
a grounded three-prong receptacle in accordance with applicable electrical codes. 

• 

This icemaker requires a standard 115 Volts A.C. 60Hz grounded electrical outlet. 

• 

It  is  recommended  to  have  a  dedicated  circuit  serving  only  the  icemaker.  Use  receptacles  that 
cannot be turned off by a switch or pull chain. 

• 

The cord should be secured behind the icemaker and not left exposed or loose. 

• 

The fuse (or circuit breaker) size should be 15 amperes. 

 

 

EXTENSION CORD 

Because of potential safety hazards, THIS APPLIANCE IS NOT RECOMMENDED FOR USE WITH AN 
EXTENSION CORD. However, if you must use an extension cord, USE ONLY A UL/CUL-Listed, 3-wire 
grounding type appliance extension cord WITH a grounding type plug and outlet. the electrical rating of 
the cord MUST be 115 volts and at least 15 amps. 

WARNING

 

IMPROPER USE OF THE GROUNDED PLUG CAN RESULT IN THE RISK OF ELECTRICAL 
SHOCK. IF THE POWER CORD IS DAMAGED, HAVE IT REPLACED BY AN AUTHORIZED 
TECHNICIAN. 

 

Summary of Contents for IM-600US















Reviews: