background image

MODEL B

HYDRAULIC TOE JACK

Model J58T Maximum Capacity: 5 Ton

Model J109T Maximum Capacity: 10 Ton

Read and carefully follow the warnings and operating instructions before using this jack. Most problems with new
equipment are caused by improper operation or setup.

NOTE: Inspect the jack upon arrival. The carrier, not the manufacturer, is responsible for any damage
resulting from shipment.

SAFETY PRECAUTIONS

W

WA

AR

RN

NIIN

NG

G::

To help prevent personal injury or damage to equipment,

Do not exceed the maximum load capacity of the jack.

Do not add additional load to a lifted load.

Do not use in unstable or hazardous positions.

Unit must be used on flat surfaces able to carry the load.

Keep clear of lifted loads.

The load must be stable during lifing. An unstable load may cause the jack or load to slip.

Do not use the jack(s) if damaged, altered, or in poor condition.

Do not lift people or loads with people on them.

This hydraulic jack is for professional use only and should be used only by persons trained in its use.

Do not lift at the end of the toe. Fully engage the load with the toe.

Use only Power Team hydraulic fluid in this unit.

Do NOT, under any circumstances, tamper with the adjustment of the jack's internal relief valve screw. To

do so may cause the jack to fail.

When lifting by the toe, wedge the head of the jack

on the load to avoid bending the column. 
Refer to illustration at right.

Read operating instructions and A.N.S.I. B30.1

safety code for jacks.

The owner of the jack must ensure that all safety-

related decals are maintained and replaced as they
become hard to read.

This guide cannot cover every situation, 

so always do the job with safety first.

Form No. 102663

Parts List and
Operating Instructions
for:

J58T
J109T

Sheet No.

1 of 4

Rev 5

Date: 20 May 2003

Tech. Services: (800) 477-8326

Fax: (800) 765-8326

Order Entry: (800) 541-1418

Fax: (800) 288-7031

SPX Corporation
5885 11th Street
Rockford, IL 61109-3699 USA

Internet Address: 

http://www.powerteam.com

®

© 2005 SPX Corporation

Summary of Contents for Power Team J109T










Reviews: