background image

1007895 Rev. D

1 YEAR LIMITED WARRANTY

This is warranted to the original purchaser only.  Spyker will replace parts 
with defects in materials and workmanship, for a period of one year from the 
date of purchase.

For Spyker Spreaders–a Brinly-Hardy Company, products employing metal 
gear systems, pinion and bevel, these metal gears, only, not inclusive of any 
other parts or materials, are warranted for the life of  the spreader, not to 
be used for replacement or repair past original purchase.

Spyker Spreaders will not be liable for any loss, damage or expense including, 
but not limited to, consequential or incidental damages, arising from the 
operation, condition or use of the item.  The sole and exclusive remedy 
against Spyker Spreaders being the replacement of the defective parts.  This 
warranty gives you specifi c legal rights, and you may also have other rights 
which vary from state to state.

This express warranty, which is applicable only to the original 
purchase, is in lieu of and excludes all other warranties, whether 
expressed or implied by operation of law or otherwise, including any 
warranty of merchantability or fi tness for particular purpose.

SPYKER SPREADERS 

Jeffersonville, IN 47130  USA

Phone: 800.972.6130

Summary of Contents for P40 Series













Reviews: