background image

Wi-Fi Smart Led Strip Light 

Welcome to use intelligent lamp series products

User Manual

IP Grade:

Power:

Voltage:
Power Supply:

Luminous Flux:

Emitting Color:
LED QTY:

CRI:
FPC Width:

Protocol:
App Control:

SMART LIFE

Wi-Fi

12mm

>80Ra

RGB+2700K-6500K

5050 (60pcs); 2835 (120pcs)

DC12V

Insert wall type, input AC90-240V/0.6A;

output DC12V/1A

IP64 (Slim PU glue potted)

SF1202WE1DP-8 

2M/Roll

8W

500lm

Voice Control:

Amazon Alexa/ Google Home

Auto Conatrol:
Certificates:

IFTTT

ETL/CE/FCC

Length:

Model:

Warning

1. IP65 water-proof Led strips can be installed indoor and outdoor area, but can't 

be under water! IP20 non water-proof Led strips can be installed indoor only.

2. All installation are required to cut off power. 

3. The voltage of this Led strip is DC12V, please use the related power supply, 

but not use AC220V to run it directly.

4. Make sure to cut at the correct position if you need to cut the strip light, the 

min cut lenght is 50mm (every 3leds as a group). The most important is, the 

cutting point not touch water otherwise there will be short circuit when light up.

Installation Instruction

1. Ensuring the clean installation surface before installing this product.

2. 1.Non-waterproof smart Led strip:

Uncovering the 3M tape on the back of Led strip light, but not rip it all off at once.

Fixing the Led strip light on the surface where you would like, avoid to press the 

Led chips.

2.2.Waterproof smart Led strip:

Use the mounting clips to firm Led strip according to your requirement.

3. Connect the black wire of strip light to the positive pole, and the red/green/blue 

and white wire to the corresponding color of the smart controller.

4. Connect the power supply to the smart controller, and light up the strip light.

Fault Checking

1. Please check if the positive and negative of power cord is wrongly connected.

2. Please check if the connection of power cord is secure and poorly connected.

3. Please check if the adapter is consistent with the voltage of strip light.

Warranty

SSLUCE Lighting warranty applies to manufacturing defects afecting its 

products which existed at the time of the purchase of the product, that are 

non-apparent, and are unknown to the buyer,for a period of 3 years. this 

warranty applies to the product only and does not cover the installation of the 

product. The warranty does not apply to material, economic and/or physical 

damages or losses caused by the product. This warranty will not apply to any 

damages and/or losses caused by an incorrect use, installation or maintenance 

of the product. The manufacturer is therefore notliable for damages to the 

product or material, economic and/or physical damages or losses caused by an 

incorrect use, installation or maintenance of the product. If the buyer considers 

that the product is afected by a defect,the buyer should return the product to the 

point of purchase or send an email to sales01(@SSLUCE.com Should the 

buyer decideto send an emaill to sales01@ssluce.com, a description of 

thealleged problem should be included in the email and a proof of purchase as 

well as the picture clearly illustrating the alleged defect should be attached to 

the email. The buyer should also return the product to SSLUCE Lighting at 

his/her own expense. After product inspection, if the warranty applies, SSLUCE 

Lighting will repair or replace the product free of charge.

R

+12V

WW

  CW

B
R
G
WW

CW

RGB

R

R

R

WW

CW

RGB

R

R

+12V
  CW

B
R
G

WW

R

+12V

WW

  CW

B
R
G
WW

CW

RGB

R

R

R

WW

CW

RGB

R

R

+12V
  CW

B
R
G

WW

Summary of Contents for Intelligent Lamp Series







Reviews: