ST. SpA CP1 434 Series, Operator'S Manual

EN - 2

Behaviour

• 

Exercise caution when reversing or moving backwards. 

Look behind you to make sure there are no obstacles 

before and during operations in reverse gear.

• 

Never run, always walk.

• 

Do not allow the lawnmower to pull you along.

• 

Always keep hands and feet away from the cutting means, 

when starting and when using the machine.

• 

Attention:  the  cutting  means  will  continue  to  rotate  for 

a  few  seconds after disengagement  or after you have 

switched off the engine.

• 

Keep away from the discharge opening.

• 

Do not touch the engine parts as they get very hot when 

running. Danger of burns.

If something breaks or an accident occurs during 

mowing, turn off the engine immediately and move 

the machine away to prevent further damage; if 

an accident occurs with injuries or third parties 

are injured, carry out the first aid measures most 

suitable for the situation immediately and contact 

the medical authorities for any necessary health 

care. Carefully remove any debris which could 

cause damage or injury to persons or animals 

if ignored.

Use limitations

• 

Never  operate  the  machine  with  damaged,  missing 

or  incorrectly  assembled  guards  (grass  catcher,  side 

discharge guards  rear discharge guards).

• 

Don’t use the machine if the attachments/tools are not 

installed in their seats.

• 

Never disengage, deactivate, remove or tamper with the 

safety systems/micro switches installed.

• 

Do not alter the engine adjustments, nor over-run it. If 

the engine is forced to work with an excessive number of 

rotations, the risk of personal injury increases.

• 

Do not strain the machine too much and do not use a 

small machine for heavy-duty work. If you use the right 

machine, you will reduce the risk of hazards and improve 

the quality of your work.

1.4.  MAINTENANCE, STORAGE AND TRANSPORT

Ensure regular maintenance and correct storage to maintain 

machine safety and high performance levels.

• 

Never  use  the  machine  with  worn  or  damaged  parts. 

Faulty or worn-out parts must always be replaced and 

never  repaired.  Use  original  replacement  parts  only: 

the use of non-original and/or incorrectly fitted parts will 

jeopardise the safety of the machine, may cause accidents 

or personal injuries for which the Manufacturer is under 

no circumstance liable or responsible. 

• 

To reduce the risk of fire, regularly check the machine for 

oil and/or fuel leaks.

• 

While adjusting the machine, pay attention to avoid getting 

your fingers caught between the moving cutting device 

and the fixed parts of the machine .

• 

Do not store the machine with fuel in the tank in an area 

where fuel vapours could reach a naked light, a spark or 

a strong heat source.

• 

To reduce fire risks, do not leave containers with debris 

inside a room.

The noise and vibration levels shown in these 

instructions are the maximum levels for use of 

the machine. The use of an unbalanced cutting 

element, the excessive speed of movement, or 

the absence of maintenance have a significant 

influence  on  noise  emissions  and  vibrations. 

Consequently, it is necessary to take preventive 

steps to eliminate possible damage due to high 

levels of noise and stress from vibration. Maintain 

the machine well, wear ear protection devices, 

and take breaks while working.

1.5.  ENVIRONMENTAL PROTECTION

• 

Scrupulously comply with local regulations for the disposal 

of  packaging,  deteriorated  parts  or  any  elements  with 

a strong environmental impact; this waste must not be 

disposed of as normal waste, it must be separated and 

taken  to  specified  waste  disposal  centres  where  the 

material will be recycled.

• 

Scrupulously comply with local regulations for the disposal 

of waste materials

• 

When  the  machine  is  withdrawn  from  service,  do  not 

dispose of it in the environment, but take it to a waste 

disposal facility in accordance with the local regulations 

in force.

2. 

PRODUCT DESCRIPTION

This machine is pedestrian controlled lawnmower.

The machine essentially consists of an engine, which drives 

a cutting device enclosed in a casing, equipped with wheels 

and a handle.

The operator is able to operate the machine and use the main 

controls, always staying behind the handle at a safe distance 

from the rotating cutting means.

If the operator leaves the machine, the engine and cutting 

means will stop within a few seconds.

Intended use and improper use

This machine is designed and built for cutting grass in gardens 

and grassy areas.

Any other usage may be hazardous and harm persons and/

or damage things.

Examples of improper use may include, but are not limited to:

• 

transporting  other  people,  children  or  animals  on  the 

machine;

• 

being transported by the machine;

• 

using the machine to tow or push loads.

• 

operate the cutting device in non grassy areas;

• 

using the machine for collecting leaves or debris;

• 

using the machine to trim hedges, or for cutting vegetation 

other than grass;

• 

use of the machine by more than one person.

 IMPORTANT 

  Improper use of the machine will invalidate the 

warranty, relieve the Manufacturer from all liability, and the user 

will consequently be liable for all and any damage or injury to 

himself or others.

This  machine  is  intended  for  use  by  consumers,  i.e.  non-

professional operators. The machine is intended for "DIY" 

use only.

 IMPORTANT

The machine must be used by one operator.