background image

196 / 196 M electronic IP65

18

en

Maintenance and upkeep 

 

The electronic spirit level is a precision instrument and should therefore be  

handled with care. 

Display window: 

 

Dirty window glass impairs the optical function.  

Only clean with a soft cloth, a little water or, if required, a mild detergent! 

 

Casing:

 

Clean the unit with a damp cloth. 

• 

Do not use solvents or thinners!

• 

Do not immerse the unit in water 

• 

Do not unscrew the electronic spirit level!

Transport and storage

• 

Remove the batteries if you do not intend to use the unit for some time!

• 

Do not store the unit when damp! 

• 

Allow the unit and carry case to dry first if  

necessary.

Recycling programme for our EU customers

 

In accordance with WEEE rules, STABILA offers to dispose of electronic products 

at the end of their useful service life.  

For more information call: 0049 / 6346 / 309-0

STABILA warranty declaration

In addition to the statutory rights of buyers, which are not limited by this 

warranty, STABILA guarantees that the unit is free from defects and has 

assured features in the event of material or manufacturing defects for a

period of 24 months from the date of purchase. Any defects / errors will

be remedied at our discretion through reworking or replacement. 

STABILA will not assume liability for further claims. Defects resulting 

from improper handling (e.g. damage due to application of serious force, 

operation with incorrect voltage / current type, use of unsuitable power 

source) and unauthorised modifications to the unit by the buyer or a third 

party shall invalidate the warranty.  

STABILA does not provide a warranty for natural signs of wear and minor 

defects that do not affect the operation of the unit. Any warranty claims 

should be made through your dealer and be accompanied by your sales 

receipt, completed certificate of warranty (see last page of operating 

instructions) and the unit itself.

Certificate of warranty for 196 / 196 M electronic IP65

Customer: 

 

 

 

Address:

 

 

 

 

 

 

Date of purchase:

 

 

 

Dealer (stamp, signature):

Technical data

Accuracy:

Electronic module
 0°   +  90° :   

 

± 0.05°

 

1°  .... 89° :   

 

± 0.2°

Spirit level  

in normal position:     

 

0.5 mm / m = 0.029°  

in reverse position:   

 

0.5 mm / m = 0.029° 

Batteries :   

 

 

2 x 1.5 V alkaline, size Mignon, AA, LR6

Operating life

 

 

 

≥ 150 hours

 

Operating temperature range: 

-10 °C   to   +50 °C

Storage temperature range: 

 

-20 °C   to   +65 °C 

Protection class: 

 

 

IP 65

Subject to technical modifications. 

 

 

 

 

      

2015

Summary of Contents for 196 electronic IP65





















Reviews: