background image

17

Stabila provides a guarantee against deficiencies and faults in the assured characte-
ristics because of material or manufacturing faults for a period of 24 months from
date of purchase. Any faults will be eliminated at Stabila's own discretion either by
repairing or replacing the unit. Stabila accepts no wider claims. 
No liability is accepted for any faults due to inappropriate treatment (e.g. damage
caused by the unit falling, operation with the wrong voltage or type of current, use of
unsuitable current supply sources) or for any autonomous changes made to the unit
by the purchaser or a third party.  
Also no claims under guarantee are accepted for natural wear and tear or any small
faults that do not significantly affect the unit's operation.
Any guarantee claims must be made via the dealer on the duly completed guarantee
form (see last page) to be returned with the unit.  

Guarantee terms and conditions

Subject to technical modifications.

Laser type:

Technical data

Self-levelling range: *:
(horizontal)

Output:

Levelling accuracy:

Batteries:

Operating life:

Operating temperature range:

Red diode laser,  wavelength 635 nm

< 1 mW, Laser Class 2 
to EN 60825-1:03-10

ca. ± 4°

± 1 mm /   0,5m

4 x 1,5 V Mignon cells Alkaline, Size AA, LR6

Approx. 40 hours

-10 °C to +45 °C

(14 °F to 113 °F)

Up Beam Accuracy*:

Down Beam Accuracy

Level Beam Accuracy*:

Square Beam Accuracy*:

± 6 mm / 21m     

± 6 mm / 30m

± 6 mm / 30m

*  At 20°C ( 50°F )

Working Range*:

20-30m  

(65–100 ft)

(    +/– 1/4 in. @ 70 ft )

(  +/– 1/16 in. @ 2.5 ft )

(  +/– 1/4 in. @ 100 ft )

(  +/– 1/4 in. @ 100 ft )

Summary of Contents for LA-4P













Reviews: