background image

en

Commissioning 

The instrument is switched on with the on/off switch (1). The side exit 

aperture (3a) is uncovered at the same time for a horizontal laser beam. 

By moving the sliding cover (5) the exit aperture (3b) is uncovered for a 

further horizontal laser beam. 

Place the laser on a level surface. The laser must be within its ±4,5° 

self-levelling range for it to align automatically.

Positioning the laser and transferring points

Plumb line function:

Release the release lever (7), extend the foot (6) and lock into position.

The LA-5PG is positioned and switched on -> switch (1). 

The down laser beam is aligned on the object or mark as required. 

Mark the position of the perpendicular laser beam on the ceiling.

Please note that the centre of laser dot is marked !

Plumbing a Wall

Release the release lever (7), extend the foot (6) and lock into position.

Position the laser in such a way that the foot (6) is on the front edge of 

the floor profile.
Switch on the instrument. -> switch (1 ). 

Illuminated green LED (2) -> laser in operation. 
Align the upper end of the partition wall until the perpendicular laser beam 

meets the upper edge of the top track.

Operating status display and error messages  

via the LED

Illuminated green LED     -> laser in operation
Illuminated red LED 

  -> battery voltage very low

laser beam flashing->     -> The unit is inclined too much 

    

 

  + is outside the self-levelling range 

     

 

  + the laser cannot level itself automatically

Replacing the batteries

Slide the battery cover (4) in the direction of the arrow and insert new 

batteries in accordance with the symbols in the battery compartment. 

Suitable batteries can also be used.

Checking the calibration

The LA-5PG point laser is designed for use on construction sites and left 

our factory perfectly adjusted.. As with any precision instrument, however, 

its calibration must be regularly checked. The unit should be checked 

before starting any new tasks, particularly when the unit has been exposed 

to strong vibrations. 

B1

B3

D1

D1

D2

D2

D3

D3

D4

D4
D5

C

B2

B4

B5

www.

GlobalTestSupply

.com

Find Quality Products Online at:

sales@GlobalTestSupply.com

Summary of Contents for LA-5PG











Reviews: