background image

 

Page | 13 

 

9. 

After the internal batteries in the UPS are connected, reinstall any panels that 

were removed and close the UPS doors.  Refer to the UPS manual for guidance 
regarding this procedure.  Do not close the Battery Cabinet circuit breakers until 
the display of the UPS shows the message: “Close Battery Switch”.  Closing the 
breakers before this may damage the UPS or blow fuses in the Battery Cabinet.  
Once the Battery cabinet circuit breakers are closed the front doors of the battery 
cabinet may be closed. 
 
Terminal blocks on the –N version cabinets are disconnected by unplugging the 
“powerpole” connectors in all cabinets.  This requires the removal of the inner 
panel by authorized personnel only. 

 
 

Table 3 - Terminal Tightening Torques and Wires Sizes 

 

BATTERY INPUT/OUTPUT TERMINAL 

TIGHTENING TORQUE

 

WIRE SIZE 

TORQUE 

#2/0 - #6 AWG 

120 inch-pounds 

 

TB4 LOW VOLTAGE TERMINAL TORQUE

 

WIRE SIZE 

TORQUE 

#10 – 26 AWG 

5.3 – 7.0 inch-pounds 

 

GROUND STUD TIGHTENING TORQUE

 

Extended Run Time Battery Cabinet 

100 inch-pounds 

UPS Cabinet 

55 inch-pounds 

 

kVA Rating 

Minimum Input/Output 

Wire Size

 

Minimum Ground Wire 

Size 

30 

#2 AWG 

#8 AWG 

 
 
*Wire must be rated 75°C or higher.  Use copper conductors only. 
 
 
 
 
 
 
 
 
 

Summary of Contents for FLP-BAT-030-150-2-N-30K






















Reviews: