background image

Operation, Installation and Maintenance Manual for 6018/11 - Series 

 
ID-No.:  

 

226765 / 6018605300 

Publication Code:           2017-08-31:BA00.lll.en.02                                                                                                                                                                               Page - 5 - of 22 

 

 

3.2 

Safe Use 

• 

Read and observe the safety notes in these operating instructions! 

• 

Observe characteristic values and rated operating conditions on the rating and data plates! 

• 

Observe additional information plates on the device! 

• 

Use the device in accordance with its intended and approved purpose only! 

• 

We cannot be held liable for damage caused by incorrect or unauthorized use or by non-compliance with these operating 
instructions. 

• 

Before installation and commissioning, make sure that the device is not damaged! 

• 

Work on the device (installation, maintenance, overhaul, repair) may only be carried out by appropriately authorized and 
trained personnel. 

 

 

Safety Notes - Warnings 

   

Use the devices only for their intended purpose!  

 

We cannot be held liable for damage caused by an incorrect or unauthorized use or by non-observance of 
these operating instructions.  

 

Use the device only if it is undamaged. 

 

The mounting arrangements must be secured with lock washers or self-locking nuts and bolts. 

 

Any unauthorized work on the device is prohibited!  

 

Installation, maintenance, overhaul and repair may only be carried out by appropriately authorized and 
trained personnel. Non-compliance to this could be fatal or could result in damage to the property 

 

Avoiding material damage 

 

Non-compliance with the instruction can result in material damage to the device and/or its environment 

3.3 

Intended Use 

The light fitting 6018 is equipment 

• 

for lighting areas, work spaces and objects 

• 

can be used indoor / Outdoor 

• 

for stationary mounting 

• 

for use in Zones 1, 2, 21 & 22 and in the safe area 

3.4 

Modification and Alterations 

 

WARNING 

Danger due to modifications and alterations to the device! Explosion protection is 
impaired! 
Non-compliance results in severe or fatal injuries. 

 

Do not modify or change the device. 

 

 

No liability or warranty for damage resulting from modifications and alterations. 

Summary of Contents for 6018/11 Series























Reviews: