background image

Explanation of the symbols

4

259910 / L40260300020

2017-09-18·BA00·III·en·00

Linear Luminaire with LED

Series EXLUX L402/2

EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN

2

Explanation of the symbols

2.1

Symbols in these operating instructions

2.2

Warning notes

Warnings must be observed under all circumstances, in order to minimize the risk due to 

construction and operation. The warning notes have the following structure:

• Signalling word: DANGER, WARNING, CAUTION, NOTICE

• Type and source of danger/damage

• Consequences of danger

• Taking countermeasures to avoid the danger or damage

Symbol

Meaning

Tips and recommendations on the use of the device

General danger

Danger due to energised parts

DANGER

Danger to persons

Non-compliance with the instruction results in severe or fatal injuries to per

-

sons.

WARNING

Danger to persons

Non-compliance with the instruction can result in severe or fatal injuries to 

persons.

CAUTION

Danger to persons

Non-compliance with the instruction can result in light injuries to persons.

NOTICE

Avoiding material damage

Non-compliance with the instruction can result in material damage to the device and / or 

its environment.

Summary of Contents for EXLUX L402/2 Series





















Reviews: