background image

259910 / L40260300020

2017-09-18·BA00·III·en·00

Safety notes 

5

Linear Luminaire with LED

Series EXLUX L402/2

EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN

2.3

Symbols on the device

3

Safety notes

3.1

Operating instructions storage

• Read the operating instructions carefully and store them at the mounting location of 

the device.

• Observe applicable documents and operating instructions of the devices to be  

connected. 

3.2

Safe use

• Read and observe the safety notes in these operating instructions!

• Observe characteristic values and rated operating conditions on the rating and data 

plates!

• Observe additional information plates on the device!

• Use the device in accordance with its intended and approved purpose only!

• We cannot be held liable for damage caused by incorrect or unauthorized use or by 

non-compliance with these operating instructions.

• Before installation and commissioning, make sure that the device is not damaged!

• Work on the device (installation, maintenance, overhaul, repair) may only be carried 

out by appropriately authorized and trained personnel.

3.3

Intended Use

The luminaire L402/2 is equipment

• for stationary mounting

• can be used indoors and outdoors

• for lighting areas, work spaces and objects

4

Function and device design

4.1

Function

• for lighting areas, work spaces and objects

Symbol

Meaning

05594E00

CE marking according to the current applicable directives.

Summary of Contents for EXLUX L402/2 Series





















Reviews: