RAM3
(
CMP30
)
C
ONTROLS
[
H/L
]
Key
Press this key to toggle the transmit power between high
and low. When the [
H/L
] key is pressed while the trans-
ceiver is on channel 13 or 67, the power will temporarily
switch from LOW to HI power until the
PTT
is released.
The [
H/L
] key does not function on transmit inhibited and
low power only channels.
PTT
(
Push-To-Talk
)
Key
Press this key to activate the transmission.
POWER
( )
Key
Press and hold down this key to turn to the transceiver
and
RAM3
(
CMP30
) “on” and “off”.
Microphone
The internal microphone is located here.
When transmitting, position your mouth about 1/2 to 1 inch
(1.2 ~ 2.5 cm) away from the small mic hole. Speak slowly
and clearly into the microphone.
DISPLAY
Channel display.
SOFT KEY
For details, refer to “
Mode Setting and Setup
” above.
KEY PAD
[
CALL/MENU
] Key
Press this key to access the DSC OPERATION menu.
Press and hold this key to access the SETUP menu.
[
16/9
] Key
First press
: channel 16 is immediately selected.
Second press
: recalls the last selected channel.
Press and hold
: selects channel 9.
[
S
](
UP
)/[
T
](
DOWN
) Key
These keys are used to select channels, adjust the vol-
ume and squelch level, and to choose DSC calls, DSC
setup and Radio setup function.
[
VOL/SQ
] Key
(Volume Control / Squelch Control)
Press this key to toggle the function of the microphone’s
[
S
] or [
T
] key between the channel selections, volume
level adjustment, and squelch level adjustment.
[
CLR/WX
] Key
For details, refer to “
Mode Setting and Setup
” above.
[
ENT
] Key
This key functions as the enter key.
Speaker
The internal speaker is located here.
[
DISTRESS
]
KEY
This key is used to send a DSC Distress Call.
Lift the red spring loaded DISTRESS cover, then press
and hold in the [
DISTRESS
] key.
M
ODE
S
ETTING
& S
ETUP
The
RAM3
(
CMP30
) is backward compatible Standard Horizon VHF radios that use the
RAM+
(
CMP25
) and
VH-310
(telephone style handset).
M
ODE
S
ELECTION
The Mode selection allows the
RAM3
(
CMP30
) to be setup to
operate with specific models, refer to the section below for
compatibility.
Mode 1
:
GX1256S
,
GX1280S
, and
GX2360S
Mode 2
:
PS1000
,
PS2000
,
CPV350
,
CPV550
,
GX1500S/E
,
GX3000S/E
,
GX3500S
Ú
,
GX5000S
,
GX5500S
,
and
VM-3500E
Ú
Ú
To use
Mode 2
on the
GX3500S
or
VM-3500E
the radio
software may have to be updated. Please contact Stan-
dard Horizon for details.
1. Turn the
RAM3
(
CMP30
) off, press
and hold the [
ENT
] key then press
and hold the orange
POWER
( )
key until the menu is shown.
2. Press the [
S
] or [
T
] key to select
“
Operation Mode
Operation Mode
Operation Mode
Operation Mode
Operation Mode
” item, then press
the [
ENT
] key.
3. Press the [
S
] or [
T
] key to select the Operation Mode
(“
Mode 1
Mode 1
Mode 1
Mode 1
Mode 1
” or “
Mode 2
Mode 2
Mode 2
Mode 2
Mode 2
”) and press the [
ENT
] key.
4. Press the [
T
] key to select “
Save &
Save &
Save &
Save &
Save &
Exit
Exit
Exit
Exit
Exit
” and press the [
ENT
] key.
K
EY
S
ETUP
The following are used only when
Mode 2
is selected
and the
RAM3
(
CMP30
) is connected to a compatible
radio.
[
CLR/WX
]
Function:
The operation of this key may be changed to select WX chan-
nels for North American market or CLR for Europe. By default
the when the key is pressed, the last selected WX channel
will be shown.
1. To change this key to operate the
CLR function, Turn the
RAM3
(
CMP30
) off, press and hold the
[
ENT
] key then press and hold the
orange
POWER
( )
key until the
menu is shown.
2. Press the [
T
] key to select “
[CLR
CLR
CLR
CLR
CLR
/
WX
WX
WX
WX
WX] Function
Function
Function
Function
Function
” and press the [
ENT
]
key.
3. Select “
CLR
CLR
CLR
CLR
CLR
” and press the [
ENT
]
key.
4. Press the [
T
] key to select “
Save &
Save &
Save &
Save &
Save &
Exit
Exit
Exit
Exit
Exit
” and press the [
ENT
] key.
Define
[
Soft
]
Keys:
By default the soft keys are assigned as SCAN, DW and NAV,
however these keys can be changed. In addition the soft keys
can be increased / assigned, refer below:
1. Turn the
RAM3
(
CMP30
) off, press
and hold the [
ENT
] key then press
and hold the orange
POWER
( )
key until the menu is shown.
2. Press the [
T
] key to select “
Define
Define
Define
Define
Define
[Soft
Soft
Soft
Soft
Soft] keys
keys
keys
keys
keys
” and press the [
ENT
] key.
3. Press the [
S
] or [
T
] key to select
the [Soft] key, and press the [
ENT
]
key. Then, press the [
S
] or [
T
] key
to select the new function to be
assigned, and press the [
ENT
] key.
Available functions are listed below.
4. Press the [
CLR/WX
] key to return
to the “Soft Key Setup” mode.
5. Press the [
T
] key to select “
Save &
Save &
Save &
Save &
Save &
Exit
Exit
Exit
Exit
Exit
” and press the [
ENT
] key.
Number of Soft Keys:
3 soft keys are set as default. However the
RAM3
(
CMP30
)
allows assigning of up to 10 soft keys with the instructions
below:
1. Turn the
RAM3
(
CMP30
) off, press
and hold the [
ENT
] key then press
and hold the orange
POWER
( )
key until the menu is shown.
2. Press the [
T
] key to select “
Num-
Num-
Num-
Num-
Num-
ber of Soft keys
ber of Soft keys
ber of Soft keys
ber of Soft keys
ber of Soft keys
” and press the [
ENT
]
key.
3. Select the number of soft keys (3,
4, 6, 8 or 10) and press the [
ENT
]
key.
4. Press the [
T
] key to select “
Save &
Save &
Save &
Save &
Save &
Exit
Exit
Exit
Exit
Exit
” and press the [
ENT
] key.
I
MPORTANT
N
OTE
Mode 2
only allows the
RAM3
(
CMP30
) to define the
[
CLR/WX
] key and assign / Change the number of se-
lectable soft keys.
DISPLAY
SCAN
DW
NAV
DIM
MEM
IC
PA
FOG
SCRM
WX
CLR
FUNCTION
Ú
Stops and starts scanning.
Stops and starts Dual Watch Scan.
Displays the GPS Navigation Data.
Enables the LCD backlight dimmer function.
When pressed memorizes a channel for scanning.
Activates the Intercom function.
Operates the PA function.
Operates the Fog Horn function.
Toggles the Voice Scrambler “on” and “off”.
Immediately recalls the previously selected US
NOAA weather channel.
Cancels the menu selection.
Ú
: Some functions may not operate depending on the connected radio.
O
PTIONAL
A
CCESSORIES
CT-100 23F
T
E
XTENSION
C
ABLE
MLS-310 10
WATT
A
MPLIFIED
S
PEAKER
MLS-300 E
XTERNAL
L
OUD
S
PEAKER
LCD S
ETTING
The
RAM3
(
CMP30
) has the capability to change the LCD
contrast by following the instructions below.
1. Press and hold down the [
CALL/MENU
] key until “
RADIO
RADIO
RADIO
RADIO
RADIO
SETUP
SETUP
SETUP
SETUP
SETUP
” menu appears.
2. Press the [
CALL/MENU
] key, then
press the [
T
] key until the “
CON-
CON-
CON-
CON-
CON-
TRAST
TRAST
TRAST
TRAST
TRAST
” menu appears.
3. Press the [
CALL/MENU
] key again,
then press the [
S
] or [
T
] key to se-
lect the desired contrast level.
4. Press the [
CALL/MENU
] key to
store the selected level, then press
the [
16/9
] key to exit “
RADIO SETUP
RADIO SETUP
RADIO SETUP
RADIO SETUP
RADIO SETUP
”
menu and return to radio operation
mode.
S
PECIFICATIONS
Supply voltage
:
13.8 VDC (Supplied from the transceiver)
Current consumption
:
700 mA @VOL Max.
200 mA @AF Mute
Operating Temperature
: –4 °F to +140 °F (–20 °C to +60 °C)
MIC. Sensitivity
(Typical): 60 mVrms
@ 1 kHz Tone with 3 kHz Deviation
MIC. Impedance
:
2 k
Ω
AF output
:
300 mW @ 16
Ω
for 10 % THD
(Internal Speaker)
2 W @ 4
Ω
for 10 % THD
(External Speaker)
Display Size
:
1.8” x 0.9” (45 x 23 mm)
Display Resolution
:
132 x 64 dot
Case Size
:
2.6” x 5.5” x 1.2” (67 x 140 x 30 mm)
Weight
(Approx):
11.6 oz (330g)
