Stanley 6-GR25, Original Instructions Manual

1

English

OPERATING INSTRUCTIONS

iMPORTAnT: 

Please read carefully before using your electric 

glue gun.

1.  Plug your glue gun into an electrical outlet.
2.  To open the fold-away-stand, take hold of the flanges on 

both sides of the stand and pull forward until the stand locks 
into position.

3.  The Stanley® Dualmelt™ Glue gun allows you to work on the 

high setting for general purpose use and the low setting for 
heat sensitive materials. High-low switch is located in center 
front of handle. Move switch to desired temperature setting. 

high temperature

 is for bonding wood, leather, ceramics 

and other non-porous materials. 

low temperature 

is 

for bonding paper, fabric, dried flowers and other heat 

Applications and Repairs

•  Woodworking
•  Plastics
•  Foam
•  Fabrics
•  Paper
•  Cardboard
•  Crevices
•  Repair book bindings, shoe or loose carpeting.
•  Sealing windows, tiles, and bathroom fixtures
•  Dried floral arrangements
•  Electrical insulation

CAUTION:

 Read Safety Rules and Operating 

Instructions Carefully.

WARNING:

 When using electric tools, basic safety 

precautions should always be followed to reduce the risk 
of fire, electrical shock and personal injury.

READ ALL SAFETY INSTRUCTIONS:

1.  Do not touch the nozzle area or melted glue.
2.  Keep work area clean. Work environment should be clean, 

dry well lit and clear of flammable materials.

3.  Guard against electric shock. Prevent body contact with 

grounded surfaces like pipes and appliances. Do not use 
near water.

4.  Inspect extension cords.
5.  Keep children away.
6.  Always use safety glasses.
7.  Don’t abuse cord. Never carry the tool by the cord or yank 

the cord to disconnect from plug or receptacle.

8.  Disconnect tools when not in use.
9.  Avoid accidental glue discharge. Do not touch the glue stick 

or trigger except to dispense glue.

10.  To reduce the risk of fire or electric shock, do not expose this 

product to rain or moisture.

11.  When not in use, the tool should be stored indoors.
12.  Do not pull glue sticks from gun. The feed mechanism may 

become damaged or impaired. If you desire to change types 
of glue, cut off protruding end and feed the remainder 
through with the new type of glue.

CAUTION:

 WHEN GUN IS HOT DO NOT LAY IT ON ITS 

SIDE. ALWAYS USE STAND. MELTED GLUE WILL BURN 
SKIN. OPERATING TEMPERATURE OF THE NOZZLE IS 
380° F (193°C). DO NOT TOUCH THE NOZZLE AREA OR 
MELTED GLUE.

Electrical Safety

Double insulated tools are equipped with a polarized plug (one 
blade is wider than the other). This plug will fit in a polarized 
outlet only one way. If the plug does not fit fully in the outlet, 
reverse the plug. If it still does not fit, contact a qualified 
electrician to install a polarized outlet. Do not change the plug 

in any way. Double insulation eliminates the need for the three 
wire grounded power cord and grounded power supply system.

Safety Precautions:

•  Do not touch nozzle area of glue gun or melted glue.
•  Do not make repairs to the glue gun.
•  Do not use a damaged glue gun.
•  Do not allow glue gun to come in contact with water, 

liquids or rain.

•  Do not carry the tool by the cord or pull cord to disconnect 

it from the outlet.

•  For interior use only.
•  Do not leave the glue gun unattended during use.
•  Do not attempt to remove unused glue from the glue gun 

after use.

•  Place the glue gun in the upright position when idle using 

the fold down stand provided.

•  Do not use this product in areas where the risk of explosion 

is present.

•  If the supply cord is damaged, it must be replaced by the 

manufacturer, its service agent or similar qualified persons in 
order to avoid a hazard.

6-GR25

Input

V

AC

230

Frequency

Hz

50

Power

W

30

English (original instructions)

Congratulations!

You have chosen a STANLEY tool. Years of experience, thorough 
product development and innovation make STANLEY one of the 
most reliable partners for professional power tool users.

Technical Data

GLUE GUN 
6-GR25