background image

False light at start

If oil is released and no flame is established the con-
trol will cut out within the safety time of: 10 seconds.

Flame failure in operation

In the event of flame failure in operation the oil sup-
ply is cut off and the control restarts the burner as
described under the heading “Normal Start”. On
flame failure, immediately after burner start, the con-
trol will initiate re-ignition.

Flame monitoring

The flame is monitored by a photocell unit. Note: In
accordance with the latest ISO and DIN standards,
type LOA activates the safety relay if the photocell
unit is exposed to light in the pre-purging period.

Control of flame signal

The photocell current is measured with a d.c.
ammeter (moving coil instrument) which is connect-
ed in series with the photocell unit. Min current for
flame indication: 35 µA.

19

11.

Find the correct position of the air adjuster 
(See Fig. 28), which gives the highest possi-
ble  reading in the range 10.4% - 11.2%, 
without exceeding a smoke No. 0-1
(Bacharach Scale).

12.

Check the oil supply for leaks from storage 
tanks via oil filter.

13.

Check if complete system is working cor-
rectly.

14.

Make sure specified clearances are adhered
to.

15.

Check flue joints are sealed correctly and 
that no escapes are present.

16.

After withdrawing the mains cable tighten 
the anti-tug gland located at the left side of 
the cooker base level.

17.

Refer to the Operation Instructions Manual 
for correct operation of the appliance and 
familiarise the occupants on the correct 
method of operating the appliance.

LEAVE ALL DOCUMENTS WITH THE END USER

FUNCTION

Normal Start

Pre-ignition and pre-purging, after 7 seconds oil
released, and the burner operates, if the flame
forms within the safety time of 10 seconds.

Post ignition after oil release:

LOA 24 - 10 seconds.

GENERAL MAINTENANCE

It is important that the user is familiar with their
cooker and that they ensure regular checks and
maintenance which can limit unnecessary break-
downs.

SERVICING

To ensure continued efficient and safe operation of
the appliance it is recommended that it is checked
and serviced as necessary at regular intervals.  The
frequency of servicing will depend upon the particu-
lar installation and usage, but in general once a year
should be adequate.

Fig. 28

Summary of Contents for BRANDON DHW

























Reviews: