Stanley DL07, Operation And Service Manual

7

The safety tag (p/n 
15875) at right is attached 
to the tool when shipped 
from the factory.  Read 
and understand the safety 
instructions listed on this 
tag before removal.  We 
suggest you retain this tag 
and attach it to the tool 
when not in use.

TOOL STICKERS & TAGS

D A N G E R

I M P O R T A N T

READ OPERATION MANUAL AND

SAFETY INSTRUCTIONS FOR THIS

TOOL BEFORE USING IT.

USE ONLY PARTS AND REPAIR

PROCEDURES APPROVED BY

STANLEY AND DESCRIBED IN THE OPERA-

TION MANUAL.

TAG TO BE REMOVED ONLY BY

TOOL OPERATOR.

SEE OTHER SIDE

1.  FAILURE TO USE HYDRAULIC HOSE 

LABELED AND CERTIFIED 

AS NON-CONDUCTIVE

 WHEN USING HYDRAULIC TOOLS 

ON OR NEAR ELECTRICAL LINES MAY RESULT IN DEATH 
OR SERIOUS INJURY.

BEFORE USING HOSE 

LABELED AND CERTIFIED AS NON-

CONDUCTIVE

 ON OR NEAR ELECTRIC LINES BE SURE THE 

HOSE IS 

MAINTAINED AS NON-CONDUCTIVE

.  THE HOSE 

SHOULD BE REGULARLY TESTED FOR ELECTRIC CURRENT 
LEAKAGE IN ACCORDANCE WITH YOUR SAFETY DEPART-
MENT INSTRUCTIONS.

2.   A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJECTION  

INTO THE BODY OR CAUSE OTHER SEVERE PERSONAL 
INJURY.

 A 

DO NOT

 EXCEED SPECIFIED FLOW AND PRESSURE FOR  

THIS TOOL.  EXCESS FLOW OR PRESSURE MAY CAUSE A  

LEAK OR BURST.

 B 

DO

NOT 

EXCEED RATED WORKING PRESSURE OF HYDRAU

    LIC HOSE USED WITH THIS TOOL.  EXCESS PRESSURE 
 

MAY CAUSE A LEAK OR BURST.

C  CHECK TOOL HOSE COUPLERS AND CONNECTORS DAILY  
 FOR 

LEAKS. 

 DO NOT

 FEEL FOR LEAKS WITH YOUR 

HANDS.CONTACT WITH A LEAK MAY RESULT IN SEVERE 

I M P O R T A N T

READ OPERATION MANUAL AND

SAFETY INSTRUCTIONS FOR THIS

TOOL BEFORE USING IT.

USE ONLY PARTS AND REPAIR

PROCEDURES APPROVED BY

STANLEY AND DESCRIBED IN THE OPERA-

TION MANUAL.

TAG TO BE REMOVED ONLY BY

TOOL OPERATOR.

SEE OTHER SIDE

D  DO NOT LIFT OR CARRY TOOL BY THE HOSES.  DO  

NOT ABUSE HOSE.  DO NOT USE KINKED, TORN OR 
DAMAGED HOSE.

3.  MAKE SURE HYDRAULIC HOSES ARE PROPERLY CONNECTED 

TO THE TOOL BEFORE PRESSURING SYSTEM.  SYSTEM 
PRESSURE HOSE MUST ALWAYS BE CONNECTED TO TOOL 
“IN” PORT.  SYSTEM RETURN HOSE MUST ALWAYS BE 
CONNECTED TO TOOL “OUT” PORT.  REVERSING CONNEC-
TIONS MAY CAUSE REVERSE TOOL OPERATION WHICH CAN 
RESULT IN SEVERE PERSONAL INJURY.

4.  DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-CEN-

TER HYDRAULIC SYSTEMS.  THIS MAY RESULT IN LOSS OF 
OTHER HYDRAULIC FUNCTIONS POWERED BY THE SAME 
SYSTEM AND/OR SEVERE PERSONAL INJURY.

5.  BYSTANDERS MAY BE INJURED IN YOUR WORK AREA.  KEEP 

BYSTANDERS CLEAR OF YOUR WORK AREA.

6.  WEAR HEARING, EYE, FOOT, HAND AND HEAD PROTEC-

TION.

7.  TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE, ALL 

TOOL REPAIR MAINTENANCE AND SERVICE MUST ONLY BE 
PERFORMED BY AUTHORIZED AND PROPERLY TRAINED 
PERSONNEL.

     (shown smaller then actual size)

SAFETY TAG P/N 15875

D A N G E R

NOTE

THE INFORMATION LISTED ON 
THE STICKERS SHOWN, MUST BE 
LEGIBLE AT ALL TIMES. 

REPLACE DECALS IF THEY 
BECOME WORN OR DAMAGED. 
REPLACEMENTS ARE AVAILABLE 
FROM YOUR LOCAL STANLEY 
DISTRIBUTOR.

28322
CE STICKER (CE)

11207
CIRCUIT TYPE D STICKER (CE)

D

30 LPM @ 138 B AR

EHTMA CATEGORY

58862
PRESSURE WARNING STICKER

28788
MANUAL STICKER (CE)

60807
DL07 MODEL STICKER

Stanley Hydraulic Tools

3810 SE Naef Road

Milwaukie, Oregon USA

26-45 LPM / 7-12 GPM

140 BAR / 2000 PSI

Model No.

IW16

DL07

4-12 GPM/15-45 LPM

2000 PSI / 140 BAR

OC/CC

FOR USE ON OPEN CENTER AND 
CLOSED CENTER HYDRAULIC 
SYSTEMS. “SET FOR PROPER SYSTEM 
BEFORE USE”

11354
OC/CC STICKER

Please refer to the parts illustration for location of stickers.

RATED NO-LOAD SPEED

1000 RPM AT

8 GPM/30 LPM

29148
RPM STICKER

WARNING

58864
ELECTRICAL WARNING STICKER