Stanley Fat Max FME1250, Manual

7

ENGLISH

(Original instructions)

Hammer drilling

u

  For hammer drilling in masonry and concrete, set the 

operating mode selector (4) to the 

 position and the 

drilling mode selector (3) to the 

 position. When ham-

mering, the tool should not bounce and run smoothly. If 

necessary, increase the speed.

Hammering

u

  For hammering with spindle lock, and for light chiselling 

and chipping, set the operating mode selector (4) to the 

 position and the drilling mode selector (3) to the 

position.

u

  When changing from hammer drilling to chiselling, turn 

the chisel to the desired position. If resistance is felt 

during mode change, slightly turn the chisel to engage the 

spindle lock.

Switching on and off 

u

  Select the required speed by turning the speed selector 

dial (2).

u

  To switch the tool on, press the on/off switch (1).

u

  To switch the tool off, release the on/off switch.

Brush monitor (fig. E)

Your tool has a built in system that monitors the health of the 

brushes.

u

  Green brush monitor indicator (17). The brushes are in 

good condition.

u

  Red brush monitor indicator (18). The brushes are warn 

and need replacing, return your tool to an authorised 

Stanley Europe Service Centre in order to to have the 

brushes replaced.

Accessories

The performance of your tool depends on the accessory used. 

Stanley Fat Max accessories are engineered to high quality 

standards and designed to enhance the performance of your 

tool. By using these accessories you will get the very best 

from your tool.

Maintenance

Your Stanley Fat Max corded/cordless appliance/tool has 

been designed to operate over a long period of time with a 

minimum of maintenance.  Continuous satisfactory operation 

depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u

  Switch off and unplug the appliance/tool.

u

  Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u

  Regularly clean the motor housing using a damp cloth. Do 

not use any abrasive or solvent-based cleaner.

u

  Regularly open the chuck and tap it to remove any dust 

from the interior (when fitted).

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

u

  Safely dispose of the old plug.

u

  Connect the brown lead to the live terminal in the new 

plug.

u

  Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal. 

Follow the fitting instructions supplied with good quality plugs. 

Recommended fuse: 5 A.

Protecting the environment

Z

Separate collection. This product must not be 

disposed of with normal household waste.

Should you find one day that your Stanley Fat Max product 

needs replacement, or if it is of no further use to you, do not 

dispose of it with household waste. Make this product avail-

able for separate collection.

z

Separate collection of used products and packag-

ing allows materials to be recycled and used again.  

Re-use of recycled materials helps prevent 

environmental pollution and reduces the demand 

for raw materials.

Local regulations may provide for separate collection of elec-

trical products from the household, at municipal waste sites or 

by the retailer when you purchase a new product.

Stanley Europe provides a facility for the collection and 

recycling of Stanley Fat Max products once they have reached 

the end of their working life. To take advantage of this service 

please return your product to any authorised repair agent who 

will collect them on our behalf.

You can check the location of your nearest authorised repair 

agent by contacting your local Stanley Europe office at 

the address indicated in this manual. Alternatively, a list of 

authorised Stanley Europe repair agents and full details of our 

after-sales service and contacts are available on the Internet 

at: www.2helpU.com