GB
12
Stanley Tools declares that the CE Mark has been applied to this
product in accordance with the CE Marking Directive 93/68/EEC.
This product conforms with IEC/EN60825-1:2014.
Batteries and Power
Battery Installation
Laser Tool Battery Installation
RL 600
See Figure
Ⓕ①
1.
Press battery compartment cover and slide out.
2.
Install two new D cell batteries. Orient batteries correctly
when placing into laser tool.
3.
Securely close and lock battery compartment cover.
Remote Control Battery Installation
RL 600L, RL 700L, and RL 750L-G
See Figure
Ⓖ②
1.
Open battery compartment by unlatching cover.
2.
Install two new AA batteries. Orient batteries correctly when
placing into laser tool.
3.
Securely close and lock battery compartment cover.
Detector Battery Installation
See Figure
Ⓒ②
1.
Open battery compartment by lifting open battery cover.
2.
Install two new AA batteries. Orient batteries correctly when
placing into laser tool.
3.
Securely close and lock battery compartment cover.
WARNING:
Pay close attention to the battery holder’s (+) and (-)
markings for proper battery insertion. Batteries must be
of same type and capacity. Do not use a combination of
batteries with different capacities remaining.
Charging the Li-ion Battery
RL 600L, RL 700L, and RL 750L-G
See Figure
Ⓕ②
1.
Plug charging/power adapter plug into charging jack of laser
tool.
2.
Plug charging/power adapter into power outlet (110 V or 220
V) with appropriate plug receptacle.
The
LED will light RED during charge.
3.
Leave battery to charge for approximately 7 hours to reach
full charge.
The
LED will light GREEN when charge is
complete.
4.
When battery is fully charged unplug the charging/power
adapter from laser tool and power outlet.
WARNING:
Charge laser only with the power adaptor
supplied. Using any other type of charger may result in
damage and/or personal harm.
Operating with Charging/Power
Adapter
•
Laser tool can operate while plugged into charging/power
adapter.
•
Functions and controls of laser tool are the same as when not
plugged into charging/power adapter.
Using the Accessories
CAUTION:
Do not leave the laser tool unattended on an
accessory without fully tightening the mounting screw.
Failing to do so may lead to the laser tool falling and
sustaining damage.
Mounting Bracket
RL 700L and RL 750L-G
See Figure
Ⓗ
NOTE:
• It is best practice to support the laser tool with one hand when
placing or removing the laser tool from an accessory.
•
If positioning over a target, partially tighten the 5/8″-11 screw
mount, align laser tool, and then fully tighten the 5/8″-11
screw mount.
1.
Securely position the Mounting Bracket using one of the
following methods:
•
Hang the Mounting Bracket from a wall using the Keyhole
Slot (Figure
Ⓗ②
).
•
Attach the Mounting Bracket to a ceiling edge using the
Ceiling Grid Clamp (Figure
Ⓗ③
).
•
Use the Keyhole Mount (Figure
Ⓗ④
) with any
compatible accessory.
Summary of Contents for Fatmax FMHT77446
