13
GB
Only use Stanley accessories that are recommended for use
with this model. Accessories that may be suitable for one laser
may create a risk of injury when used with another laser.
The bottom of the laser is equipped with 1/4-20 and 5/8-11
female threads (Figure
C
) to accommodate current or future
Stanley accessories. Only use Stanley accessories specified
for use with this laser. Follow the directions included with the
accessory.
Recommended accessories for use with this laser are available
at extra cost from your local dealer or authorized service center.
If you need assistance locating any accessory, please contact
your nearest Stanley service center or visit our website:
http://www.2helpU.com
.
Maintenance
•
When the laser is not in use, clean the exterior parts with
a damp cloth, wipe the laser with a soft dry cloth to make
sure it is dry, and then store the laser in the kit box provided.
•
Although the laser exterior is solvent resistant, NEVER use
solvents to clean the laser.
•
Do not store the laser at temperatures below -20 ˚C (-5 ˚F) or
above 60 ˚C (140 ˚F).
•
To maintain the accuracy of your work, check the laser often
to make sure it is properly calibrated.
Calibration checks and other maintenance repairs may be
performed by Stanley service centers.
Troubleshooting
The Laser Does Not Turn On
•
Make sure the laser’s Li-ion battery is fully-charged.
•
Be sure to keep the laser dry.
•
If the laser unit is heated above 50 ˚C (120 ˚F), the unit will
not turn ON. If the laser has been stored in extremely hot
temperatures, allow it to cool. The laser level will not be
damaged by using the Power/Transport Lock switch before
cooling to its proper operating temperature.
The Laser Beams Flash
The lasers are designed to self-level up to an average of
4° in all directions. If the laser is tilted so much that the
internal mechanism cannot level itself, the laser beams will
flash indicating that the tilt range has been exceeded. THE
FLASHING BEAMS CREATED BY THE LASER ARE NOT
LEVEL OR PLUMB AND SHOULD NOT BE USED FOR
DETERMINING OR MARKING LEVEL OR PLUMB. Try
repositioning the laser on a more level surface.
The Laser Beams Will Not Stop Moving
The laser is a precision instrument. Therefore, if it is not
positioned on a stable (and motionless) surface, the laser will
continue to try to find level. If the beam will not stop moving, try
placing the laser on a more stable surface. Also, try to make
sure that the surface is relatively flat and level, so that the laser
is stable.
Service and Repairs
Note:
Disassembling the laser level will void all warranties on
the product.
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by
authorized service centers. Service or maintenance performed
by unqualified personnel may result in a risk of injury. To locate
your nearest Stanley service center, go to
http://www.2helpU.com
.
Summary of Contents for Fatmax FMHT77617
