PCI140CA
140 WATT POWER INVERTER
INSTRUCTION MANUAL
SAVE THIS INSTRUCTION MANUAL FOR FUTURE
REFERENCE.
© 2021 Baccus Global LLC
Boca Raton, FL 33487
1-877-571-2391
SAFETY GUIDELINES /
DEFINITIONS
DANGER:
Indicates an imminently hazardous situation which, if not avoided,
will
result in
death or
serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided,
may
result in
death or
serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided,
may
result in
minor or
moderate injury.
Used without the word, indicates a safety related message.
NOTICE:
Indicates a practice
not related to personal injury
which, if not avoided,
may
result in
property
damage.
RISK OF UNSAFE OPERATION.
When using tools or equipment, basic safety precautions should always
be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools
or equipment could result in serious injury and property damage. There are certain applications for which
tools and equipment are designed. Manufacturer strongly recommends that this product NOT be modified
and/or used for any application other than for which it was designed. Read and understand all warnings and
operating instructions before using any tool or equipment.
READ ALL INSTRUCTIONS
WARNING:
Read and understand this instruction manual before using this unit. Failure to
follow all instructions listed below may result in electric shock, fire and/or serious injury.
IMPORTANT SAFETY
INSTRUCTIONS
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
•
Avoid dangerous environments.
Don’t use inverters in damp or wet locations.
•
Keep children away.
Keep away from children. This is not a toy!
•
Store indoors.
When not in use, inverters should be stored indoors in dry, and high or locked-up places – out
of reach of children.
•
DIsconnect the inverter
from the power supply when not in use.
•
Proper cooling is essential
when operating the inverter. Do not place it near a vehicle’s heat vent or in
direct sunlight.
•
Use of accessories and attachments:
The use of any accessory or attachment not recommended by
manufacturer for use with this inverter could be hazardous.
•
Stay alert.
Use common sense. Do not operate inverter when you are tired.
•
Check for damaged parts.
Any part that is damaged should be properly repaired or replaced by
manufacturer unless otherwise indicated elsewhere in this instruction manual before further use.
•
Do not operate
the inverter near flammable liquids or in gaseous or explosive atmospheres. Motors in tools
or appliances used with the inverter may spark, and the sparks might ignite fumes.
SPECIFIC SAFETY INSTRUCTIONS FOR INVERTERS
WARNING –
To reduce the risk of electric shock:
• Do not make any electrical connections or disconnections in areas designated as
ignition protected.
This
includes DC cigarette lighter type plug connection. This unit is NOT approved for ignition protected areas.
• Never immerse the inverter in water or any other liquid, or use when wet.
• Do not insert foreign objects into the inverter’s AC Outlet or USB Ports.
WARNING –
To reduce the risk of fire:
• Make sure that the 12 volt outlet is free of debris and the inverter fits tightly in the outlet.
• Do not operate near flammable materials, fumes or gases.
• Do not expose to extreme heat or flames.
• If the vehicle accessory outlet fuse opens (blows) when plugging in this inverter, do not use this inverter with
this vehicle accessory outlet:
– Do not repeatedly replace the fuse.
– Do not replace the vehicle accessory outlet fuse with one of a higher amperage rating.
– Never attempt to patch the fuse with tin foil or wire.
Any of these actions may cause serious electrical damage and/or a fire.
This inverter is rated to draw 9.5 amperes from a 12V vehicle outlet. Ensure that the engine system in your
vehicle can supply sufficient energy to the inverter without causing the vehicle accessory outlet fuse to open.
The fuse must be rated higher than 12 amps. Information on the vehicle accessory fuse ratings are typically
found in the vehicle operator’s manual.
CAUTION –
To reduce the risk of injury or property damage:
• It is not necessary (or desirable) to turn your vehicle on to operate this inverter. Simply turn the engine switch
to the accessory (ACC) position. Or turn on the running lights (the small lights that surround the car).
• If the inverter shuts down repeatedly, the car battery charge may be low. Discontinue inverter use to avoid
draining the battery.
• Disconnect appliance plug from inverter outlet before working on the appliance.
• Do not attempt to connect or set up the inverter or its components while operating your vehicle. Not paying
attention to the road may result in a serious accident.
• Always use the inverter where there is adequate ventilation. Do not block ventilation slots.
• Always turn the inverter off by disconnecting it from the power source when not in use.
• Make sure the nominal powering voltage is 12 volts DC, center connection positive (+).
• Do not use with positive ground electrical systems.* Reverse polarity connection will result in a blown fuse
and may cause permanent damage to the inverter and will void warranty.
*The majority of modern automobiles, RVs and trucks are negative ground.
• Keep in mind that this inverter will not operate high wattage appliances or equipment that produces heat,
such as coffee makers, hair dryers, microwave ovens and toasters.
• Do not open the inverter — there are no user-serviceable parts inside. Opening the inverter will void
manufacturer’s warranty.
• Do not use this inverter with medical devices. It is not tested for medical applications.
• Install and operate inverter only as described in this Instruction Manual.
SAVE THESE INSTRUCTIONS
WARNING –
To reduce the risk of injury or property damage:
Follow these instructions and those
published by the manufacturer of any equipment you intend to use with this inverter. Review cautionary
markings on these products.
INTRODUCTION
Congratulations on purchasing your new
Stanley
®
Fatmax
®
140 Watt Power Inverter
.
Read this
Instruction Manual and follow the instructions carefully before using your new inverter.
This power inverter is configured to supply continuous power in the form of 120 volt AC outlet and two 5 volt
USB charging ports to power most household or electronic appliances.
FEATURES
2
1
3
4
5
7
6
8
9
1. Three-Prong 120 Volt AC Outlet
2. USB Power Ports
3. On/Off Button with bi-color Power/Fault LED
Indicator
4. Mounting Clip
5. Holes for attaching the Mounting Clip
6. Mounting clip release button
7. 12V DC Accessory Plug
8. Mounting Clip Screws (2 pcs.) (KA3x10)
9. Mounting Clip Double-Sided Tape (2 pcs.)
HOW THIS INVERTER WORKS
This inverter is an electronic device that converts low voltage DC (direct current) electricity from a battery to
120 volts AC (alternating current) household power. It converts power in two stages. The first stage is a DC-to-
DC conversion process that raises the low voltage DC at the inverter input to 145 volts DC. The second stage is
a MOSFET bridge stage that converts the high voltage DC into 120 volts, 60 Hz AC.
Power Inverter Output Waveform
The AC output waveform of this inverter is known as a modified sine wave. It is a stepped waveform that has
characteristics similar to the sine wave shape of utility power. This type of waveform is suitable for most AC
loads, including linear and switching power supplies used in electronic equipment, transformers, and small
motors.
CAUTION:
If the product does not operate normally, to reduce the risk of injury or property damage,
turn the product off immediately and unplug it from the inverter.
Rechargeable Devices
• Certain rechargeable devices are designed to be charged by plugging them directly into an AC receptacle.
These devices may damage the inverter or the charging circuit.
• When using a rechargeable device, monitor its temperature for the initial ten minutes of use to determine if
it produces excessive heat.
• If excessive heat is produced, this indicates the device should not be used with this inverter.
• This problem does not occur with most of the battery-operated equipment. Most of these devices use a
separate charger or transformer that is plugged into an AC receptacle.
• The inverter is capable of running most chargers and transformers.
Certain products contain power supplies or circuits that are not compatible with an inverter using a
modified sine wave output (such as this inverter) and may be damaged by using this inverter.
Some products must be powered from a pure sine wave power source, such as standard household power, or
a “pure sine wave” inverter in order to function properly. If your product requires pure sine wave AC input
power to function properly, the instruction manual for your product could state this. If in doubt, you should
contact your product manufacturer PRIOR TO USE.
Your product could be damaged by this inverter if it contains:
• Microwave ovens;
• Transformerless battery chargers
• Capacitive coupled power supplies
If an incompatible product is used with this inverter:
• The product might not operate at all, with no indication of failure. The product fuse might open as a result of
trying to use it with the inverter.
• The product might exhibit unusual operation (such as, intermittent operation, buzzing, and the like.)
Note:
Some laptop computers may not operate with this inverter.
Rated Versus Actual Current Draw of Equipment
Most electrical tools, appliances, electronic devices and audio/visual equipment have labels that indicate the
power consumption in amps or watts. Be sure that the power consumption of the item to be operated is below
140 watts for 20 minutes, 120 watts for 60 minutes and 100 watts continuous or the unit may overheat and
shut down. If the power consumption is rated in amps AC, simply multiply by the AC volts (120) to determine
the wattage.
Resistive loads are the easiest for the inverter to run; however, it will not run larger resistive loads (such as
electric stoves and heaters), which require far more wattage than the inverter can deliver. Inductive loads (such
as TVs and stereos) require more current to operate than do resistive loads of the same wattage rating.
For safety reasons, the inverter will simply shut down if it is overloaded. To restart the unit, simply unplug all
devices plugged into the inverter; disconnect the inverter from any 12 volt DC power source; then reconnect
the inverter BEFORE plugging the appliance(s) back in.
Protective Features
The inverter monitors the following conditions:
Input Voltage Too Low:
This condition is not harmful to the inverter, but could damage the power source, so
the inverter will automatically shut down when input voltage drops below 10.5 ± 0.5 volts DC.
Input Voltage Too High:
The inverter will automatically shut down when DC input voltage exceeds 16 ± 0.5
volts, as this can harm the unit.
Thermal Shutdown Protection:
The inverter will automatically shut down when the unit becomes
overheated.
Overload/Short Circuit Protection:
The inverter will automatically shut down when an overload or short
circuit occurs.
Note:
The Power/Fault LED Indicator will light red to indicate an input voltage too low, input voltage too high or thermal fault condition OR
flash red and blue to indicate an overload or short circuit fault condition before automatic shutdown occurs.
Operating Tips
DRY — Do not allow water or other liquids to come into contact with the inverter.
COOL — Surrounding air temperature should ideally be 10-20°C (50-68°F). Keep the inverter away from direct
sunlight, when possible.
WELL-VENTILATED — Keep the area surrounding the inverter clear to ensure free air circulation around the
unit. Do not place items on or over the inverter during operation. The unit will shut down if the internal
temperature gets too hot. The inverter will auto-reset after it cools down.
SAFE — Do not use the inverter near flammable materials or in any locations that may accumulate flammable
fumes or gases. This is an electrical appliance that can briefly spark when electrical connections are made or
broken.
MOUNTING THE UNIT USING THE MOUNTING CLIP
The unit can be mounted on any flat, secure surface, especially inside the vehicle, by installing the mounting
clip located at the back of unit.
1. Press the mounting clip release button at the top of unit and simultaneously slide the mounting clip off
the back of the inverter.
2. Mount the mounting clip with two supplied KA3x10 screws or the two supplied pieces of double-sided
tape on any flat, secure surface.
3. To attach the inverter to the mounting clip, slide the unit into the mounting clip until you hear a “click”
indicating the unit is secured in place.
4. To detach the unit, press and hold the mounting clip release button on the top of unit and gently slide it
off the mounting clip.
NOTICE –
To reduce the risk of property damage:
• Only use the mounting clip for mounting the inverter. The mounting clip is not intended to support
additional weight. Do not attach to or hang anything from the mounted inverter.
• When disconnecting an appliance from the mounted inverter, use one hand to hold the mounted inverter in
place and gently unplug the appliance with the other hand. Otherwise, the inverter could be unseated from
the mounting and fall.
• Always press and hold the mounting clip release button to gently slide the inverter off the mounting clip.
Attempting to slide the inverter without holding the mounting clip release button or forcing the inverter in
any way could damage the locking mechanism.
OPERATING INSTRUCTIONS
The power/fault LED indicator lights blue when the inverter is properly connected to a functioning DC power
source and the on/off button is pressed to turn the unit on. The AC and USB outlets are ready to use. (If
the power/fault LED indicator lights red or flashes red and blue, refer to the Troubleshooting Section of this
Instruction Manual.)
To turn the unit off, press the on/off button to turn the unit off, then disconnect it from the 12 volt DC power
source.
NOTICE –
To reduce the risk of property damage:
• The Power Inverter must be connected only to batteries with a nominal output voltage of 12 volts. The unit
will not operate from a 6 volt battery and will sustain permanent damage if connected to a 24 volt battery.
• Always connect the inverter to the 12 volt DC power source before plugging any devices into the unit.
• The standard North American 120 volt AC and USB outlets allow simultaneous operation of multiple devices.
Simply plug the equipment into the unit and operate normally.
Note:
Ensure that the wattage of all equipment simultaneously plugged into the inverter does not exceed 140 watts for 20 minutes, 120
watts for 60 minutes and 100 watts continuous or the unit may overheat and shut down.
Operation of the 120 Volt AC Outlet and USB Power Ports
1. Connect the unit’s 12V DC Accessory Plug to a vehicle’s accessory outlet or other 12 volt DC power source.
Make sure there is adequate space for proper ventilation of the inverter.
2. Rotate the plug slightly to make sure there is good contact.
3. Press the on/off button to turn the inverter on.
4. The bi-color power/fault LED indicator will light blue, indicating a proper connection. If the bi-color power/
fault LED indicator lights red or flashes red and blue, a fault condition exists. Refer to the Troubleshooting
Section of this Instruction Manual.
5. Plug the (110/120 volt AC) appliance into the inverter’s three-prong AC outlet and/or plug the USB-
powered devices into the inverter’s USB power ports and operate normally.
Notes:
If the inverter does not work, make sure the ignition/accessory switch is actually powering the accessory outlet. Some vehicles require the
ignition switch to be turned on.
Some laptop computers may not operate with this inverter.
The inverter will not operate appliances and equipment that generate heat, such as hair dryers, electric blankets, microwave ovens and
toasters.
This inverter’s USB power ports do not support data communication. The ports only provide a total of 2A (5V each) to external USB-
powered devices.
Some USB-powered household electronics may not operate with these USB power ports. Check the manual of the corresponding
electronic device to confirm that it can be used with this type of USB power port.
NOTICE –
To reduce the risk of property damage:
Remember to turn the inverter off and disconnect it
from any power source when it is not in use. Also remember to turn off the accessory outlet switch to avoid
draining’s the vehicle’s battery.
CARE AND MAINTENANCE
Storage
1. Ideal storage temperature range is 0-35°C (32-104°F).
2. Store and use the inverter in a cool, dry place with adequate ventilation for all-around air circulation.
3. Avoid locations that are exposed to heating units, radiators, direct sunlight, or excessive humidity or
dampness.
Fuse Replacement
If the inverter is overloaded, and the blue LED is not lit, the internal 12 amp fuse may be blown. To replace
the fuse:
1. Unscrew the flange of the plug (counterclockwise).
2. Remove the end contact, flange and fuse.
3. Inspect the fuse to see if it is good or blown.
4. Replace with a new 12 amp fuse, if needed.
5. Carefully reassemble the fuse, end contact and flange. Do not overtighten the flange (clockwise).
TROUBLESHOOTING
Common Audio Problems
Buzzing Sound In Audio Systems
Some inexpensive stereo systems and boom boxes make a buzzing sound when operated from the inverter,
because the power supply in the electronic device does not properly filter the modified sine wave produced by
the inverter. The only solution to this problem is to use a sound system that has a higher quality power supply.
Common Power Output Problems
Input voltage below 10.5 volts
Recharge auto battery or check DC power supply.
Equipment being operated draws too much power
Reduce load to maximum 140 watts for 20 minutes, 120 watts for 60 minutes, 100 watts continuous.
Inverter in thermal shutdown condition
Allow inverter to cool down. Ensure there is adequate ventilation around the unit and that the load is no more
than 100 watts for continuous operation.
AC output is shorted
Unplug the AC appliance. Disconnect the unit from any 12 volt DC power source. Check the appliance cord.
ACCESSORIES
Recommended accessories for use with your tool may be available from the manufacturer. If you need
assistance regarding accessories, please contact the manufacturer at 1-877-571-2391.
The use of any accessory not recommended for use with this appliance could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at
1-877-571-2391.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period of ONE (1)
YEAR from the date of retail purchase by the original end-user purchaser (“Warranty Period”).
If there is a defect and a valid claim is received within the Warranty Period, the defective product can
be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or
replacement at manufacturer’s option. Proof of purchase may be required by manufacturer. (2) Return the
product to the retailer where product was purchased for an exchange (provided that the store is a participating
retailer). Returns to retailer should be made within the time period of the retailer’s return policy for exchanges
only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for
their specific return policy regarding returns that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and
tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse,
abuse; and failure to follow instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which
vary from state to state or province to province. This product is not intended for commercial use.
Please visit our website www.baccusglobal.com/register to register your new Baccus Global LLC product and to
be kept up to date on new products and special offers.
SPECIFICATIONS
DC input:
12V DC, 9.5 amps
AC output:
120V AC, 60Hz, 140 watts (for 20 minutes), 120 watts (for 60 minutes), 100
watts continuous
Output waveform:
Modified Sine Wave
USB power ports:
5V DC each (2A total)
DC plug fuse:
12A/250V AC
STANLEY
®
AND THE STANLEY
®
LOGO ARE REGISTERED TRADEMARKS
OF STANLEY BLACK + DECKER INC. OR ONE OF ITS AFFILIATES,
AND ARE USED UNDER LICENSE.
Imported by Baccus Global LLC,
621 NW 53rd St., Suite 450, Boca Raton, FL 33487
www.baccusglobal.com 1-877-571-2391
RD032521
PCI140CA_ManualENFR_032521.indd 1
PCI140CA_ManualENFR_032521.indd 1
3/25/2021 4:50:50 PM
3/25/2021 4:50:50 PM
