Stanley MA900n, Installation And Owner'S Manual

switch that

TDM

Universal Time Delay Module 

INSTALLATION INSTRUCTIONS

8701 Castle Park Drive 

„

 Indianapolis, Indiana 46256

Telephone: (800) 842-2545/(317) 842-2545 

„

 www.mssedco.com 

„

 custsvc@mssedco.com

Page 5

(82A044)  TDMv0605

FIGURE 4—Vestibule Sequencing

Once the TDM has been wired for the above application, programming of the device is as follows:

1)  Apply power to the unit.  The display will flash double bars (

––

) indicating that the unit is in its normal 

operating ready mode.

2)  To begin programming, depress the 

PROGRAM MODE BUTTON

 one time.  The first parameter to be 

programmed will appear on the display.  This is the delay time, or "on time" of the output #1 and is 

 displayed 

as 

d1

 followed by the time setting of 

2.0

 (Factory Setting) which indicates 2.0 seconds (It 

will flash between the two).  This is the time duration that you want the interior door to remain open 

(It's usually set around 4-5 seconds).  To adjust the time setting, use a small screwdriver and rotate 

 the 

DISPLAY ADJUSTMENT

 clockwise to increase and counterclockwise to decrease the time setting.  

After the desired value is displayed, depress the 

PROGRAM MODE BUTTON

 again to save the value.  

The display will now read 

d2

.  

d2

 is the delay time or "on time" of output #2.  This is the time setting 

that you want for the exterior door to remain open.  This is usually set around 4-5 seconds.  To adjust 

the setting, rotate the 

DISPLAY ADJUSTMENT

 until the desired value is displayed and then depress 

 the 

PROGRAM MODE BUTTON

.  The display should then read 

d3

.  This is the setting for the delay 

time between the activation of the interior door and the exterior door.  This time is usually set around 

1-4 seconds.  Again, adjust the setting and then depress the 

PROGRAM MODE BUTTON

.  The display 

should now read 

d4.

  This is the delay time between the opening of the doors going in the opposite 

direction.  Adjust this value in the same manner as before.  When the 

PROGRAM MODE BUTTON

 is 

 depressed, 

i1

 will then be displayed.  Now wait 30 seconds until the double bars (

––

) appear, 

indicating that the unit is in its normal operating ready mode.

3)  You are now ready to test your installation.  If any of the time settings need to be changed, make the 
 

change and press the 

PROGRAM MODE BUTTON

 once to save the new value.  Then wait 30 seconds

until the double bars (

––

) appear again, indicating that the unit is in its normal operating mode.

4)  During operation of the unit, the display will indicate its operating status.  Please refer to Figure 5 at 
 

the end of this installation manual.

PROGRAMMING 
PROCEDURE

MS SEDCO

MS SEDCO

TDM

TDM

Timing Control Module

Timing Control Module

12-24V

12-24V

AC / DC

AC / DC

      Interior

Door Operator

      Control

      Interior

Door Operator

      Control

     Exterior

Door Operator

     Control

     Exterior

Door Operator

     Control

N.O.

N.O.

N.O.

N.O.

Output #1

Output #1

Output #2

Output #2

GRAY

GRAY

WHT

WHT

BROWN

BROWN

YEL

YEL

G

R

N

GRN

G

R

N

GRN

Wall

Wall

Interior

Interior

Switch

Switch

PUSH

PUSH

TO 

TO 

OPEN

OPEN

BLU

BLU

WHT / BLU

WHT / BLU

Wall

Wall

Exterior

Exterior

Switch

Switch

PUSH

PUSH

TO 

TO 

OPEN

OPEN

WHT / GRN

WHT / GRN

WHT / RED

WHT / RED

WHT / VIO

WHT / VIO

WHT / GRAY

WHT / GRAY

WHT / BROWN

WHT / BROWN

switch that 

opens interior

door

switch that 

opens interior

door

switch that 

opens exterior

door

opens exterior

door

These optional switches are 

mounted inside the vestibule

These optional switches are 

mounted inside the vestibule

Jumper installed for 

   "DRY" contacts

Jumper installed for 

   "DRY" contacts

input #1

input #1

input #2

input #2

input #4

input #4

input #3

input #3

TDM

TDM

IN

PU

T 

4

INPUT 4

IN

PU

T 

3

INPUT 3

IN

PU

T 

2

INPUT 2

IN

PU

T 

1

INPUT 1

12

-2

4V

 A

C

/D

C

12-24V AC/DC

IN

PU

T 

1

INPUT 1

C

O

M
COM

C

O

M
COM

C

O

M
COM

C

O

M
COM

N

.O

.
N.

O

.

N

.C

.
N.

C.

N

.C

.
N.

C.

N

.O

.
N.

O.

PROGRAM

PROGRAM

MODE BUTTON

MODE BUTTON

DISPLAY

DISPLAY
ADJUSTMENT

ADJUSTMENT

LED DISPLAY KEY

LED DISPLAY KEY

d1 = delay 1

d1 = delay 1
d2 = delay 2

d2 = delay 2
d3 = delay d1 to d2

d3 = delay d1 to d2
d4 = delay d2 to d1

d4 = delay d2 to d1
i1 = input 1 (n.o. / n.c.)

i1 = input 1 (n.o. / n.c.)

i3 = input 3 (n.o. / n.c.)

i3 = input 3 (n.o. / n.c.)

i2 = input 2 (n.o. / n.c.)

i2 = input 2 (n.o. / n.c.)

i4 = input 4 (n.o. / n.c.)

i4 = input 4 (n.o. / n.c.)

o2 = output 2 (n.o. / n.c.)

o2 = output 2 (n.o. / n.c.)

o1 = output 1 (n.o. / n.c.)

o1 = output 1 (n.o. / n.c.)

o1

=

 d

ry

o1= dry

o1

=

 w

et

o1= wet

Output #1

Output #1

Output #2

Output #2