17
77-318 / 77-319
Example:
• D
1
= 5 m, D
2
= 2,0 mm, D
3
= 1,5 mm
• 0,4
mm
m
x 5 m = 2,0 mm
(maximum offset distance)
• 2,0 mm and 1,5 mm ≤ 2,0 mm
(TRUE, tool is within
calibration)
Level Beam Accuracy
(SLP5 only) -
(Horizontal Beam) -
(See fi gure
S
)
•
S
1
Place laser tool as shown with laser ON. Mark point P
1
.
•
S
2
Rotate laser tool 180° and mark point P
2
.
•
S
3
Move laser tool close to wall and mark point P
3
at cross.
•
S
4
Rotate laser tool 180° and mark point P
4
at cross.
•
S
5
Measure the vertical distance between P
1
and P
3
to get
D
3
and the vertical distance between P
2
and P
4
to get D
4
.
• Calculate the maximum offset distance and compare to the
difference of D
3
and D
4
as shown in the equation.
• If the sum is not less than or equal to the calculated
maximum offset distance the tool must be returned to
your Stanley Distributor for calibration.
Maximum Offset Distance:
= 0,2 mm
m x (D
1
m - (2 x D
2
m))
Maximum
= 0,0024 in
ft x (D
1
ft - (2 x D
2
ft))
Compare : (See fi gure
S
5
)
D
3
- D
4
≤ ± Maximum
Example:
• D
1
= 10 m, D
2
= 0,5 m
• D
3
= 0,6 mm
• D
4
= - 0,4 mm
• 0,2
mm
m
x (10 m - (2 x 0,5 m) = 1,8 mm
(maximum
offset distance)
• (0,4 mm) - (- 0,6 mm) = 1,0 mm
1,0 mm ≤ 1,8 mm
(TRUE, tool is within calibration)
Horizontal Beam Accuracy
(SLP5 only) -
(Horizontal Beam) -
(See fi gure
T
)
•
T
1
Place laser tool as shown with laser ON. Roughly aim
the laser tool towards the fi rst corner or a set reference
point. Measure out half of the distance D
1
and mark
point P
1
.
•
T
2
Rotate and roughly aim laser tool towards point P
1
.
Mark point P
2
so that it is vertically in line with point P
1
.
•
T
3
Rotate laser tool and roughly aim towards the second
corner or set reference point. Mark point P
3
so that it is
vertically in line with points P
1
and P
2
.
•
T
4
Measure the vertical distance D
2
between the highest
and lowest point.
• Calculate the maximum offset distance and compare to D
2
.
• If
D
2
is not less than or equal to the calculated
maximum offset distance the tool must be returned to
your Stanley Distributor for calibration.
Maximum Offset Distance:
= 0,2 mm
m x D
1
m
Maximum
= 0,0024 in
ft x D
1
ft
Compare: (See fi gure
T
4
)
D
2
≤ Maximum
Example:
• D
1
= 5 m, D
2
= 0,65 mm
• 0,2
mm
m x 5 m = 1,0 mm
(maximum offset distance)
• 0,65 mm ≤ 1,0 mm
(TRUE, tool is within calibration)
Summary of Contents for SLP3
