TECHNICAL DATA:
Please look at the technical table marked * at the end of this manual.
PROBLEM
CAUSE
CORRECTION
Failure to cycle
Air supply restriction
Check air supply equipment
Tool dry, lack of lubrication
Use STANLEY BOSTITCH Air Tool Lubricant
Worn head valve O-rings (if present)
Replace O-rings
Broken cylinder cap spring
Replace cylinder cap spring
Head valve (if present) stuck in cap
Disassemble/Check/Lubricate
Lack of power; slow to cycle
Air pressure too low
Check air supply equipment
Tool dry, lacks lubrication
Use STANLEY BOSTITCH Air Tool Lubricant
Broken cylinder cap spring
Replace cylinder cap spring
O-rings/seals cut or cracked
Replace O-rings/seals
Exhaust blocked
Check bumper, head valve spring, muffler
Trigger assembly worn/leaks
Replace trigger assembly
Cylinder sleeve not seated correctly on bottom bumper Disassemble to correct
Head valve dry
Disassemble/lubricate
Trigger valve housing leaking air.
O-ring cut or cracked
Replace O-ring
Trigger valve stem leaks air
O-rings/seals cut or cracked
Replace O-rings/seals
Frame/nose leaks air
O-ring or gasket is cut or cracked
Replace O-ring or gasket
Bumper cracked/worn
Replace bumper
Frame/cap leaks air
Damaged gasket or seal
Replace gasket or seal
Cracked/worn head valve bumper
Replace bumper
Loose cap screws
Tighten and recheck
Skipping fasteners; intermittent feed
Worn bumper
Replace bumper
Air restriction/inadequate air flow through quick
disconnect socket and plug
Replace quick disconnect fittings
Worn piston O-ring (if present)
Replace O-ring, check driver
Tool dry, lacks lubrication
Use STANLEY BOSTITCH Air Tool Lubricant
Damaged pusher spring
Replace spring
Low air pressure
Check air supply system to tool
Loose magazine nose screws
Tighten all screws
Fasteners too short for tool
Use only recommended fasteners
Bent fasteners
Discontinue using these fasteners
Wrong size fasteners
Use only recommended fasteners
Leaking head cap gasket
Tighten screws/replace gasket
Trigger valve O-ring cut/worn
Replace O-ring
Broken/chipped driver
Replace driver (check piston O-ring)
Dry/dirty magazine
Clean/lubricate use STANLEY BOSTITCH Air Tool Lubricant
Worn magazine
Replace magazine
Fasteners jam in tool
Driver channel worn
Replace nose/check door
Wrong size fasteners
Use only recommended fasteners
Bent fasteners
Discontinue using these fasteners
Loose magazine/nose screws
Tighten all screws
Broken/chipped driver
Replace driver (check piston O-ring)
A
Length mm.
K
Air consumption per shot @ 5.6 Bar
B
Height mm.
L
Activation type
C
Width mm.
M
Summer lubricant
D
Weight Kg.
N
Winter lubricant
E
Noise L
pa
, 1s, d
O
O-ring lubricant
F
Noise L
wa
, 1s, d
P
Fastener Name
G
Noise L
pa
, 1s, 1m
Q
Dimensions mm.
H
Vibration m/s
2
R
Head/crown
I
P max Bar
S
Magazine capacity
J
P min Bar
T
New Driver Length mm.
U
Max. Depth Inside Piston mm.
TROUBLESHOOTING
l
Disconnect the tool from the air supply and empty the magazine completely before proceeding.
l
If the problem cannot be resolved using the guide below, Contact your nearest Stanley representative or distributor.
GB
©Stanley Bostitch. Not to be reproduced without permission. Unauthorised copies of this
document do not constitute CE compliance for the products.
F
©Stanley Bostitch. Reproduction interdite sans permission préalable. Les copies non autorisées
de ce document ne signifient en rien que les produits soient conformes aux normes CE.
D
©Stanley Bostitch. Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte
Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.
NL
©Stanley Bostitch. Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige
kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.
DK
©Stanley Bostitch. Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument
udgør ikke CE overholdelse for produkterne.
SF
©Stanley Bostitch. Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt
kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.
G
©Stanley Bostitch. Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη
εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για
τα προϊόντα.
I
©Stanley Bostitch. Vietata la riproduzione senza permesso. Le copie non autorizzate di questo
documento non garantiscono la conformità CE per i relativi prodotti.
N
©Stanley Bostitch. Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette
dokumentet oppfyller ikke kravene for CE-merking for produktet.
P
©Stanley Bostitch. Reprodução proibida sem autorização prévia. As cópias não autorizadas
deste documento não estão em conformidade com a CE para os produtos.
E
©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
S
©Stanley Bostitch. Prohibida la reproducción sin permiso. Las copias no autorizadas de este
documento no suponen la conformidad con las normas CE de los productos.
PL
©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
prezentowanych produktów.
CZ
©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.
Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE
prezentowanych produktów.
SK
©Stanley Bostitch. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto
dokumentu nie sú v súlade s CE pre dané výrobky.
HU
©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül
sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.
