UNPACKING
Remove all parts from the shipping crate and verify that the following parts were included in your shipment:
Description
Qty.
Installation Instructions E-TR & E-TRx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Tie Strap, 14* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screw, Truss Head, #10-24 x 3/4* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Screw, Pan Head, M4x.7, 19mm* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Frame Assembly w/ Motor Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Top Rail with Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Neck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Side Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Screw, Button Head Socket Cap, 1/4”-28 UNC x 3/8”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Screw, Socket Head Cap, 5/16”-18 UNC x 1.0”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Bolt, Socket Head Cap, 5/16”-18 UNC x 3.0”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Washer, Flat, 5/16” I.D. x 1.2” O.D.* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Washer, Split Lock, 5/16”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Hex (Allen) key, 1/4”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hex (Allen) key, 5/32”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screwdriver, Phillips, #2* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screwdriver (blade-tip), 3/32”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Owner’s Manual with Warranty Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
*Part of included
STAR TRAC
tool kit.
**E-TRe & E-TRxe models will have embedded touch screen and surrounding plastics packaged separately.
Should any component not be present or if you have any operational questions, please call Star Trac’s Customer Care department at
(800) 503-1221 or USA 1-714-669-1660. Specifically refer to your treadmill serial number and model number listed below:
Serial No._________________________________________________________________________
Model No._________________________________________________________________________
NOTE
: The following assembly procedure applies to the E SERIES Treadmills.
ASSEMBLY
The following tools are required for assembly: Hex (Allen) Key, 1/4”; Hex (Allen) Key, 5/32”; Screwdriver, Phillips. To assemble your
STAR TRAC E SERIES TREADMILL
, just follow these steps.
NOTE
: Don’t fully tighten bolts and screws until all parts are assembled.
1.
Unpacking and Positioning the Frame Assembly
Remove all the packaging material so the treadmill is sitting, ready for
assembly, on the shipping crate platform. With a helper, lift the tread-
mill frame assembly from the shipping crate platform and place it in
the location where it will be used. Make sure the unit is placed near a
power outlet.
Caution:
The motor shroud end of the frame assembly is very heavy.
Two people may be needed to lift this end when moving the frame
assembly.
A
SSEMBLY AND
S
ETUP
C
HAPTER
2
STAR TRAC E SERIES TREADMILL O
WNER
’
S
M
ANUAL
11
