background image

2

© Copyright 2018 Star Water Systems. All rights reserved.

This product is warranted for one year from the date of purchase or two 

years from the date of manufacture, whichever occurs first.  Subject 

to the conditions hereinafter set forth, the manufacturer will repair or 

replace to the original consumer, any portion of the product which proves 

defective due to defective materials or workmanship. To obtain warranty 

service, contact the dealer from whom the product was purchased. The 

manufacturer retains the sole right and option to determine whether to 

repair or replace defective equipment, parts or components. Damage 

due to conditions beyond the control of the manufacturer is not covered 

by this warranty.

THIS WARRANTY WILL NOT APPLY: 

(a) To defects or malfunctions 

resulting from failure to properly install, operate or maintain the unit in 

accordance with printed instructions provided; (b) to failures resulting 

from abuse, accident or negligence or use of inappropriate chemicals or 

additives in the water; (c) to normal maintenance services and the parts 

used in connection with such service; (d) to units which are not installed 

in accordance with normal applicable local codes, ordinances and good 

trade practices; and (e) the unit is used for purposes other than for what 

it was designed and manufactured.

RETURN OF WARRANTED COMPONENTS:

 Any item to be repaired 

or replaced under this warranty must be returned to the manufacturer 

at Kendallville, Indiana or such other place as the manufacturer may 

designate, freight prepaid.

Limited Warranty

THE WARRANTY PROVIDED HEREIN IS IN LIEU OF ALL OTHER 

EXPRESS WARRANTIES, AND MAY NOT BE EXTENDED OR 

MODIFIED BY ANYONE. ANY IMPLIED WARRANTIES SHALL BE 

LIMITED TO THE PERIOD OF THE LIMITED WARRANTY AND 

THEREAFTER ALL SUCH IMPLIED WARRANTIES ARE DISCLAIMED 

AND EXCLUDED. THE MANUFACTURER SHALL NOT, UNDER ANY 

CIRCUMSTANCES, BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL 

OR SPECIAL DAMAGES, SUCH AS, BUT NOT LIMITED TO DAMAGE 

TO, OR LOSS OF, OTHER PROPERTY OR EQUIPMENT, LOSS 

OF PROFITS, INCONVENIENCE , OR OTHER INCIDENTAL OR 

CONSEQUENTIAL DAMAGES OF ANY TYPE OR NATURE. THE 

LIABILITY OF THE MANUFACTURER SHALL NOT EXCEED THE 

PRICE OF THE PRODUCT UPON WHICH SUCH LIABILITY  IS 

BASED.

This warranty gives you specific legal rights, and you may have 

other rights which vary from state to state. Some states do not allow 

limitations on duration of implied warranties or exclusion of incidental or 

consequential damages, so the above limitations may not apply to you.

Maintenance Guidelines

  Cleaning of Reservoir and Impeller:

  1)  Remove entire pump from wall, if mounted.

  2)  Disassemble reservoir from the deck by removing the four screws located at the corners of the deck.

  3)  Remove the impeller cover by loosening the five screws on the underside of the motor. Remove the impeller shaft 

assembly.

  4)  Wipe off the gasket between the impeller & the motor housing with a damp cloth.

  5)  Reassemble impeller to the motor, then reassemble reservoir to the deck.

 

Cleaning of Check Valve:

 

1)  Remove discharge line from valve.

  2)  Remove check valve with 9/16” wrench.

  3)  Visually check for obstructions or damage.

  4)  Replace valve by hand tightening, then tighten 1/2 turn with a 9/16” wrench. 

  

 Do not overtighten, damage to the O-ring seal may occur.

Servicing of a Double-Insulated Appliance

In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means 

is provided on a double-insulated product, nor should a means for grounding be added to the product. Servicing a 

double-insulated product requires extreme care and knowledge of the system, and should be done only by qualified 

service personnel. A double-insulated product is marked with the words “DOUBLE-INSULATION” or “DOUBLE-

INSULATED”.

In those instances where damages are incurred as a result 

of an alleged pump failure, the Homeowner must retain 

possession of the pump for investigation purposes.

Summary of Contents for COND-1









Reviews: