background image

7

STACKING INSTRUCTIONS

The following instructions should be followed when stacking 

more than one unit.

Single Oven (or Bottom) Cart Install:

1. Remove door, conveyor, and finger assemblies.

2. Unbolt unit from shipping crate (2 bolts).
3. Turn unit on front as shown.
4. Thread the four legs into the bottom of the oven.
5. CAREFULLY lift oven upright.

Stacked Oven Install Preparation:

1. Remove door, conveyor, and finger assemblies.

2. Unbolt unit from shipping crate (2 bolts).
3. Turn unit on front as shown.
4. Remove top of lower oven (4 screws total, 2 each front and rear)

and bolt to stacked oven base using 3/8 - 16 bolts.

5. Place top oven on lower unit and re-attach with screws for top of

lower oven.

OPERATING INSTRUCTIONS

DO NOT ATTEMPT TO OPERATE THE OVEN until connection of 

utility service and installation has been fully inspected (start-up check-

out) by an authorized service technician or a Star Service Technician 

in order to assure the oven is properly installed and in working order.  

The warranty becomes effective upon verification of proper 

installation.

Unless specified otherwise, conveyor travel is factory set for left to right operation when facing the 

front of the oven.  If a direction change is required, refer to "DISPLAY INFORMATION," section 3 for 

instructions on how to program the controller for a direction change.  In addition, the conveyor belt 

must be changed to travel in the new direction.

SAFETY OPERATING INSTRUCTIONS

The information contained in this section is provided for the use of qualified operating personnel.  

Qualified operating personnel are those who have carefully read the information contained in this 

manual, are familiar with the functions of the oven and/or have had previous experience with the 

operation of the equipment described.  Adherence to the procedures recommended herein will assure 

the achievement of optimum performance and long, trouble-free service.

CAUTION

DO NOT WORK AROUND THE CONVEYOR BELT 

WITH LONG HAIR, LOOSE CLOTHING, OR DANGLING 

JEWELRY.  GETTING CAUGHT IN THE BELT COULD 

RESULT IN DISMEMBERMENT OR FATAL INJURY.

Summary of Contents for Holman Ultra-Max UM1833A













































Reviews: