background image

OM-EZ505E

Classification of Devices

Type of protection against electric shock :

- Class II equipment :

Degree of protection against electric shock :

- Type B applied part :

Method of sterilization or disinfection recommended by the manufacture :

- Refer to  7. Sterilization

Degree of safety of application in the presence of a flammable anesthetic mixture with air or with oxygen or  
nitrousoxide :

- EQUIPMENT not suitable for use in the presence of a flammable anaesthetic mixture with air or with oxygen or  

nitrous oxide.

Mode of operation :

- Continuous operation

Classification

Degree and severity of danger or damage

WARNING

Explains an instruction where personal injury or physical damage may occur.

C A U T I O N

Explains an instruction where minor to medium injury or physical damage may occur.

N O T I C E

Explains an instruction that should be observed for safety reasons.

Read this manual thoroughly before use and operate the device properly.
These instructions will show you how to operate the product safety and prevent danger to you or others.  They are  

  

 

classified by the degree and/or severity of danger. All contents relating to safety should be oberserved.

Cautions for handling and operation

Please Read this operation manual carefully before use and keep for future reference. 

 OPERATION MANUAL

Thank you for purchasing the NuTorque

®

 Lite. Read this Operation Manual carefully before use for operation instructions and care and 

maintenance guidelines. Keep this Operation Manual for future reference.

Application

This motor is used for cutting / polishing of the tooth.

User

Dentist and dental assistant.

Prohibition

This motor is dental treatment use only.  Do not use for Oral Surgical treatment.

CAUTION:

 Federal law restricts this device to sale by or on the order of a dentist. 

Electric Handpiece System

Summary of Contents for NuTorque Lite














Reviews: