background image

5. System Management

5.1 System Architecture

Quick Volume and RAID Set Setup

>

RAID Set Functions

>

Create RAID Set 

>

Delete RAID Set 

>

Expand RAID Set

>

Activate RAID Set

>

Create Hot Spare

>

Delete Hot Spare

>

Rescue RAID Set

Volume Set Functions 

>

Create Volume Set

>

Modify Volume Set

>

Check Volume Set 

>

Stop Volume Set Check 

Physical Drive

>

Create Pass-Through

>

Modify Pass-Through

>

Delete Pass-Through

>

Identify Drive

>

Identify Drive

System Controls

>

System Config 

>

EtherNet Config

>

Alert By Mail Config

>

SNMP Configuration

>

NTP Configuration

>

View Events/Mute Beeper

>

Generate Test Event 

>

Clear Event Buffer

>

Modify Password

>

Upgrade Firmware

>

Restart Controller

>

Raid Set Hierarchy

Information

>

System information

>

Hardware Monitor

When your  computer  has  booted, your operating system  should recognize the RAID  volume automatically. 
After  the  volume has  been successfully recognized, please  follow  the formatting  of  hard drive  instructions 
given by the operating system to format the drive volume of your preference. Once the formatting has  been 
completed, the RAID system is ready for use.

Note : 
The  actual  storage  capacities  may  differ  from  the  stated  capacities  on  the  hard  drives  once  the 
drives have been formatted.

SOHORAID SR5 Series User Manual

10

Summary of Contents for Sohoraid SR5 Series






















Reviews: