background image

>> 14

 • Instruction manual • Staring Mega 300

1. There will be a guarantee of 12 months from date of delivery.

2. The guarantee cover all operational failures due to material or fabrication defects.

3. The manufacturer can choose freely to remedy the damage by compensation, 

 

replacement or repair.

4. The costs of dispatch are on the account of the buyer.

5. Replaced parts belong to Staring Maskinfabrik A/S.

6. The manufacturer will undertaker no responsibility with regard to consequential damages 

 

and possible loss of production.

7. In order for the guarantee to be complied with the defect must be reported immediately after 

 

it has occurred.

    

THE GUARANTEE DOES NOT COVER

1. Damages due to incorrect connection.

2. Repair executed by others.

3. Damage as a result of wrong operation, negligent treatment or transportation damages.

4. Natural wear and tear.

5. Only use approved Staring spare parts.

Where a complaint is forthcoming Staring Maskinfabrik A/S should be informed in writing together 

with all relevant information regarding the machine. Additionally, an, defective symptoms or cause 

must be informed.

>> 13. Guarantee

Summary of Contents for Mega 300

















Reviews: