background image

WARRANTY 

 

Your    StarLogixs     CybaMICRO 2011   Controller    is guaranteed against  faulty 
workmanship or components for a period of twelve months after the purchase date. 
For warranty contact your local  sales   agent  with  proof of  purchase date. 
 
This warranty does not cover damage or failure cause by or attributable to Acts of 
God, abuse, misuse, improper maintenance, lightning or other incidence of exces-
sive voltage or any repairs other   than  those  provided  by   an  authorised Star-
Logixs service facility, or transportation costs. 
 
StarLogixs  is  not  responsible  or  liable  for  indirect,  special,  or  consequential  dam-
ages arising out of or in connection with the use or performance of the Controller or 
other   damages  with  respect to  any  economic loss, loss of property, loss of reve-
nues   or  profit,  or  cost  of  removal, installation or reinstallation. 
 
There will be charges rendered for repairs to the product made after the expiration 
of the aforesaid twelve month warranty period. 
 

 

This  warranty  gives  you  specific  legal  rights  and  you  may  have  other  rights 
which vary from state to state.  

13 Carl Baer Circuit 

 

DEEPWATER. N.S.W. 2371 Australia 

Phone: (02) 67 345 262 Fax: (02) 67 345 020 

www.starlogixs.com.au 

 

 

Page 16 

10.0 Warranty 

10.1 Copyright 

 
Copyright 2001 by Starlogixs Pty Ltd. 
All rights reserved.  
The contents of this document, CybaMICRO 2011Controller front panel artwork, printed cir-
cuit board artwork, and firmware (programs contained in Controller integrated circuits) are 
subject to copyright and can not be reproduced, transmitted into any language or computer 
language, in any form or any means, electronic, mechanical, magnetic, optical, chemical, 
manual, or otherwise, without prior written consent from Starlogixs Pty. Ltd.   
                       

5.2 Trademarks 
 

The symbols                                          
 
are subject to Australian and international Trademark registrations, and their use is expressly 
prohibited without written consent from StarLogixs Pty Ltd.                                                                                   
 

 

Summary of Contents for CybaMICRO 2011

















Reviews: