background image

1

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support

Compliance Statements

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class 

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed 

to provide reasonable protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more of the following 

measures:

•  Reorient or relocate the receiving antenna

•  Increase the separation between the equipment and receiver

•  Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected

•  Consult the dealer or an experienced radio/TV technician for help

For the State of California

WARNING: Cancer and Reproductive Harm 

www.P65Warnings.ca.gov

Use of Trademarks, Registered Trademarks, and other 

Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and 

other protected names and/or symbols of third-party companies not related in 

any way to StarTech.com.  Where they occur these references are for illustrative 

purposes only and do not represent an endorsement of a product or service 

by StarTech.com, or an endorsement of the product(s) to which this manual 

applies by the third-party company in question.  Regardless of any direct 

acknowledgement elsewhere in the body of this document, StarTech.com 

hereby acknowledges that all trademarks, registered trademarks, service marks, 

and other protected names and/or symbols contained in this manual and 

related documents are the property of their respective holders.

Summary of Contents for 8STSDOCK1EU3P2






















Reviews: