Disconnecting a Drive
Warning!
If you remove the drive before you receive the notification that it’s safe to
do so, you could experience lost or corrupted data.
If the
Host Computer’s
OS is Windows, complete the following steps:
Windows PC
1. On the
Notification
tray, click the
Safely Remove Hardware and Eject Media
icon.
2. Click the storage device that you want to remove.
3. When the message appears indicating that
it’s safe to remove the device
,
disconnect the drive.
If the
Host Computer’s
OS is macOS, complete the following steps:
macOS
1. Close any windows that list the contents of the drive.
2. On your desktop, click and drag the
USB Storage
icon onto the
Trash Can
icon on
your desktop.
3. Wait 5 seconds, then disconnect the drive.
8. Gently slide the
Connector
on the
Drive
at a 30-degree angle into the corresponding
Drive Connector
on the
Drive Tray
.
Note:
The
Connector
on the
Drive
is keyed so that it only fits one way.
9. Lightly push the
Drive
down into position on the
Drive Tray
.
10. Insert the
Drive-Mount Screw
through the screw hole in the
Drive
and into the
Drive-Mount Standoff
.
11. Tighten the
Drive-Mount Screw
, using a
Phillips Head Screwdriver
. Do not over-
tighten.
12. Slide the
Drive Tray
into the center grooves in the enclosure so that the
USB-C Port
is facing outward.
13. Place the
Cover Plate
over the
USB-C Port
and circuit board. Secure the
Cover Plate
in place by inserting two
Drive-Tray Screws
on either side of the
USB-C Port
on the
front of the enclosure and tighten, using a
Phillips Head Screwdriver
.
Connecting a Drive to a Computer
When the enclosure is connected to the
Computer
the OS will automatically install the
necessary software.
Note:
The enclosure does not require an external power supply, as it receives enough
power through the USB port that it is connected to.
• Connect the
USB-C to USB-C Cable
or the
USB-A to USB-C Cable
to the
USB-C Port
on the
Enclosure
and to a
USB Port
on the
Computer
.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss
of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください
。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
