7
6
3. USE
EN
•
When sanding metal, sparks are generated; do not use dustbox/vacuum cleaner
and keep other persons and combustible material from work area.
•
Do not touch the moving sanding sheet.
•
Do not continue to use worn, torn or heavily clogged sanding sheets.
•
Wear protective gloves, safety glasses, close-fitting clothes and hair protection
(for long hair).
•
Always disconnect plug from power source before making any adjustment or
changing any accessory.
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•
Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to
the earth terminal of the plug.
USE
Mounting of sanding sheet
•
Disconnect the plug
•
The dust suction requires the use of perforated sanding sheets
•
Perforation in sanding sheet should correspond with perforation in sanding foot
•
Replace worn sanding sheets in time
•
Always use the tool with the total sanding surface covered with sanding paper
Switch
- switch on/off the tool by pushing switch (1) forward/backwards (2 positions)
Speed adjustment
Selecting frequency vibrations produced by rotating the wheel (2) of the regulator
oscillation frequency.
- The minimum frequency (≈5000 / min.) corresponds to the value "1"
- The maximum frequency (≈12000 / min.) - corresponds to the value of "MAX".
Selection of the oscillation frequency depends on the type of work, type processed
material and grain size sanding paper.
4. APPLICATION ADVICE
EN
5. MAINTENANCE / SERVICE / SPECIFICATION
• Dust suction
- empty dustbox (3) regularly for optimal dust pick-up performance
For using vacuum cleaner
- Remove dustbox (3)
- Connect the vacuum cleaner nozzle to the eccentric grinding machine.
Inner diameter connecting pipe - 30 mm.
• Do not use dust box / vacuum cleaner when sanding metal
Holding and guiding the tool
- guide the tool parallel to the working surface
• Do not apply too much pressure on the tool; let the sanding surface do the
work for you
- do not tilt the tool in order to avoid unwanted sanding marks
• While working, always hold the tool firmly with both hands
- keep ventilation slots uncovered
APPLICATION ADVICE
•
Use the tool with the delta-tip pointing forward for edged, narrow and other hard-to-
- reach places
•
Use the tool with the flat side pointing forward for long strokes on flat surfaces
•
For sanding curved workpieces as well as for sanding with high removal performance
use the tool in combination with backing pad A
•
Use the tool with the special sanding attachments for hard-to-reach places
•
Never use the same sanding sheet for wood and metal
•
Recommended sanding sheet grits:
coarse
- for removing paint; for sanding of extremely rough wood
medium
- for sanding of rough or plain wood
fine
- for smoothing of wood; for finishing of bare wood
•
Use different grit sizes when the working surface is rough:
- start sanding with coarse or medium grit
- finish with fine grit
MAINTENANCE / SERVICE
•
This tool is not intended for professional use
•
Always keep tool and cord clean (especially ventilation slots)
- remove adhering sanding dust with a brush
• disconnect the plug before cleaning
•
If the tool should fail despite the care taken in manufacturing and testing procedures,
repair should be carried out by an after-sales service centre for STATUS power tools
ENVIRONMENT
• Do not dispose of electric tools, accessories and packaging together with
household waste material (only for EU countries)
- in observance of European Directive 2012/19/EC on waste of electric and electronic
equipment and its implementation in accordance with national law, electric tools that
have reached the end of their life must be collected separately and returned to an
environmentally compatible recycling facility
220-240V~ 50Hz
ACCESSORIES
Sander XS2-125ET,
d
ust box,
manual, packing.
SPECIFI
CATION
Rating voltage
Rating power
No load speed
Weight
300 W
5000 - 12000 RPM
1,4 kg
