gb
/
20
/
AS-XP
Filter dimensions ....................................110 x 90 x 9 mm
Vision area
..................................................... 92 x 42 mm
Degree of protection, clear state ..............................4DIN
Degree of protection, dark state ..........................9/13DIN
Degree of protection for grinding ..............................2DIN
Protection against inferred and ultraviolet ..............16DIN
Interval between clear to dark
...................... 1/25000 sec
Internal between dark to clear
........................
0.2/0.8 sec
Sensibility.
............................................................. manual
Power supply
....................................................solar cells
Operating Temperature
.......................................
-5 -55 ºC
Weight
.............................................................500 grams
Filter safe worklife
................................................. 2 years
AS-XL
Filter dimensions ..................................114 x 133 x 9 mm
Vision area
................................................... 100 x 60 mm
Degree of protection, clear state ..............................4DIN
Degree of protection, dark state.................... 5/9-9/13DIN
Protection against inferred and ultraviolet ..............16DIN
Interval between clear to dark
...................... 1/30000 sec
Internal between dark to clear
........................
0.2/0.8 sec
Sensibility.
............................................................. manual
Power supply
....................................................solar cells
Operating Temperature
.......................................
-5 -55 ºC
Weight
.............................................................440 grams
Filter safe worklife
................................................. 2 years
6. USER INSTUCTIONS
Adjusting the mask to the user.
In the models AS-X / AS-XP / AS-1D. Adjustments may
vary do to different sizes of users head. To correctly adjust
the equipment to individual users, follow the proceeding
instructions.
1.
Adjust the height of the head
: Adjust the upper band
of the harness (8), adjust the length of the band so
that it sits on the head in a way that the eyes are at the
height of the filter with the mask perpendicular to the
horizon and the harness is parallel to the horizon.
2.
Adjustment of the perimeter to the head:
Adjust the
adjustment knob (10) by pushing and turning until the
harness sits comfortably without too much slack or too
much pressure.
3.
Adjust the angle of vision
: Loosen screws (13),
Lift and turn the work angle adjustment deck (9) in a
way that the upper part of the mask is in its working
position (stopper of the harness resting in the stopper
of the deck (9) ) an angle of 10º to 15º towards the
face of the user.
Adjusting protection angle
AS-X / AS-R / CARNIVAL / AS-XP / AS-1D AS-RT .Adjust
knob (4) using the following table based in UNE EN
379:2004/A1:2010.
These tables are valid for mid class work conditions where
the distance between the operators eyes and the base of
the molten metal is approximately 50 cm and the middle
brightness is around 100 lx.
30
40 60 70 100 125 150 175
200
225 250
300
350 400 450 500 600
9
10
11
12
12
11
10
9
10
11
12
13
13
13
12
11
10
10
11
12
9
13
13
12
11
10
9
9
10
11
12
13
13
12
11
10
9
NOTE – The tern “heavy materials” applies to steel, alloy steel, copper and its alloys, etc..
Micro plasma
Arc welding
Plasma
Jet cutting
Finish-to-air arc
MIG with light
Alloys
MIG with heavy
Metals
TIG
MAG
Process
30
40 60 70 100 125 150 175
200
225 250
300
350 400 450 500 600
Current intensity (A)
Recommended use of different degrees of protection to EN 169 arc weldin
g
Coated electrodes
