DEUTSCH
3.4.- Werkzeugwechsel (HD15K/HD17K/
f
Ziehen Sie vor allen Arbeiten am Elektro-
werkzeug den Netzstecker aus der Steck-
dose.
Reinigen Sie den Werkzeugschaft
16
und fetten Sie
ihn leicht ein.
Ziehen Sie den Sperrbolzen
15
heraus und drehen
Sie ihn um 180° entgegen dem Uhrzeigersinn.
Lassen Sie
15
wieder einrasten.
den Sperrbolzen
Führen Sie das Einsatzwerkzeug bis zum Anschlag
in
. Die Nut des
die Werkzeugaufnahme
Werkzeug
16
muss wie im Bild gezeigt nach
oben weisen.
schaftes
Überprüfen Sie die Verriegelung durch Ziehen
am Werkzeug.
4.- Betrieb
4.1.- Inbetriebnahme
f
Beachten Sie die Netzspannung! Die Span-
nung der Stromquelle muss mit den Anga-
ben auf dem Typenschild des Elektrowerk-
zeuges übereinstimmen. Mit 230 V
gekennzeichnete Elektrowerkzeuge können
auch an 220 V betrieben werden.
Betriebsart einstellen
Mit dem Umschalter “
11
Bohren/
“
Hammerbohren“
9
wählen Sie die Betriebsart des Elektrowerkzeugs.
Drücken Sie zum Wechsel der Betriebsart die
Entriegelungstaste
8
und drehen Sie den Um-
schalter „Bohren/Hammerbohren“
9
in die ge-
wünschte Position, bis er hörbar einrastet.
Hinweis:
Ändern Sie die Betriebsart nur bei aus-
geschaltetem Elektrowerkzeug! Das Elektro-
werkzeug kann sonst beschädigt werden.
Position zum Hammer-
bohren in Beton oder
Stein.
HD5K,HD5BK,MH6K: 8´
Position zum
Bohren
oh-
ne Schlag in Holz, Metall,
Keramik und Kunststoff
sowie zum Schrauben
und Gewindeschneiden
Position zum Verstellen
der Meißelposition
Position zum Meißeln
HD5K,HD5BK, MH6K: 8'
Drehrichtung einstellen
Mit dem Drehrichtungsumschalter
5
können Sie
die Drehrichtung des Elektrowerkzeuges ändern.
Bei gedrücktem Ein-/Ausschalter
7
ist dies je-
doch nicht möglich.
Rechtslauf:
Drehen Sie den Drehrichtungs-
umschalter
5
beidseitig bis zum Anschlag in
Position
.
Linkslauf:
Drehen Sie den Drehrichtungs-
umschalter
5
beidseitig bis zum Anschlag in
Position
.
Stellen Sie die Drehrichtung zum Hammerbohren,
Bohren und Meißeln immer auf Rechtslauf.
Sie können den Tragegriff
13
ummontieren.
Schrauben
ganz ab und
ziehen Sie danach die Sechskantschraube nach
oben heraus. Ziehen Sie den Tragegriff
13
seitlich
ab und schwenken Sie das verbleibende Spannteil
um 180°. Montieren Sie den Tragegriff
13
in
umgekehrter Reihenfolge.
Sie die Rändelmutter
14
MH2K / MH6K / MH8K)
29
29
Positionieren Meißeln
Vario-Lock (HD9CK)
Der Meißel 12 an Winkeln positioniert werden.
So kann die optimale Arbeitsposition für jede
Anwendung eingestellt werden.
Legen Sie den Meißel in der
Werkzeugaufnahme
- Schieben Sie den Ring
18
nach vorn und
drehen Sie den Meißel in die gewünschte
Position.
- Lassen Sie den Ring
18
, um die Position zu
verriegeln.
Summary of Contents for HD21K
