Always wait until the machine has come to a complete
stop before placing it down.
The tool insert can jam and
lead to loss of control over the power tool.
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and
storage, set the rotational direction switch to the centre
position.
Unintentional actuation of the On/Off switch can
lead to injuries.
Protect the power tool against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture.
Danger of explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints.
The vapours can
irritate the respiratory system.
Safety Warnings for battery chargers
Keep the battery charger away from rain or
moisture.
Penetration of water in the battery charger
increases the risk of an electric shock.
Do not charge other batteries.
The battery charger is
suitable only for charging
STAYER
lithium ion batteries
within the listed voltage range. Otherwise there is danger of
fire and explosion.
Keep the battery charger clean.
Contamination can lead
to danger of an electric shock.
Before each use, check the battery charger, cable and
plug. If damage is detected, do not use the battery
charger. Never open the battery charger yourself. Have
repairs performed only by a qualified technician and
only using original spare parts.
Damaged battery
chargers, cables and plugs increase the risk of an electric
shock.
Do not operate the battery charger on easily
inflammable surfaces (e. g., paper, textiles, etc.) or
surroundings
. The heating of the battery charger during
the charging process can pose a fire hazard.
Children should be supervised to ensure that they do
not play with the battery charger.
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and
storage, set the rotational direction switch to the centre
position.
Unintentional actuation of the On/Off switch can lead to
injuries.
3.Instructions for use
3.1 Placement Tool
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
3.2 Assembly (Fig. B)
The machine is intended for hammer drilling in concrete,
brick and stone. It is also suitable for drilling without impact
in wood, metal, ceramic and plastic. Machines with
electronic control and right/left rotation are also suitable for
screwdriving.
Use the battery charger only when you fully understand and
can perform all functions without limitation, or have
received appropriate instructions.
Wear hearing protection.
Exposure to noise can cause
hearing loss.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
or fastener may contact hidden wiring.
Cutting
accessory and fasteners contacting a “live” wire may make
exposed metal parts of the power tool “live” and could give
the operator an electric shock.
Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility
company for assistance.
Contact with electric lines can
lead to fire and electric shock. Damaging a gas line can lead
to explosion. Penetrating a water line causes property
damage or may cause an electric shock.
Switch off the power tool immediately when the tool
insert jams. Be prepared for high reaction torque that
can cause kickback.
The tool insert jams when:
— the power tool is subject to overload or
— it becomes wedged in the workpiece.
Secure the workpiece.
A workpiece clamped with
clamping devices or in a vice is held more secure than by
hand.
Keep your workplace clean.
Blends of materials are
particularly dangerous. Dust from light alloys can burn or
explode.
1. Contents
page
2.Specific safety instructions
......................................15
3.Instructions for use
....................................................15
3.1 Placement Tool.............................................................15
3.2 Assembly......................................................................15
3.3 Electrical connection.............................................16
3.4 Illustrated description............................................16
4.Operating instructions
..............................................16
4.1 Placement and testing..........................................16
4.2 General instructions for use..................................17
4.3 Tool change..........................................................17
5.Maintenance and service instructions
.....................17
5.1 Cleaning...............................................................17
5.2 Repair service.......................................................18
5.3 Warranty...............................................................18
5.4 Disposal and recycling..........................................18
6.Regulations
................................................................18
6.1 Technical Data......................................................18
6.2 EU declaration of conformity.................................19
2. Specific safety instructions
ENGLISH
5
5
