Battery Charging
Do not use other battery chargers.
The supplied battery
charger is designed for the Lithium- Ion battery in your
machine.
Observe the mains voltage!
The voltage of the power
supply must correspond with the data given on the
nameplate of the battery charger. Battery chargers marked
with 230 V can also be operated with 220 V.
The battery is supplied partially charged. To
ensure full capacity of the battery, completely
charge the battery in the battery charger before
using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
When the battery is empty, the machine is switched off by
means of a protective circuit: The inserted tool no longer
rotates.
Do not continue to press the On/Off switch after
the machine has been automatically switched
off.
The battery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of
between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
The charging procedure begins as soon as the mains plug
of the battery charger is plugged into a socket outlet and the
charge connector
17
is plugged into the socket
16
on the
bottom of the handle.
The battery charge-control indicator
5
indicates the
charging progress. During the charging process, the
indicator flashes green. When the battery charge-control
indicator
5
lights up green continuously, the battery is fully
charged.
During the charging procedure, the handle of the machine
warms up. This is normal. Disconnect the battery charger
from the mains supply when not using it for longer periods.
The power tool cannot be used during the charge
procedure; it is not defective when inoperative during the
charging procedure.
Protect the battery charger against moisture!
Observe the notes for disposal.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of the
user or bystanders.
Certain dusts, such as oak or beech dust, are considered as
carcinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative).
Materials containing asbestos may only be worked by
specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filterclass respirator.
Observe the relevant regulations in your country for the
materials to be worked.
The status indicator on charger, consists of two
LEDs
:
1
SDS-PLUS tool holder
2
Dust protection cap
3
Locking sleeve
4
Selector switch for drilling/hammer drilling
5
Battery charge-control indicator
6
Indicator for right rotation
*
7
Indicator for left rotation
*
8
Rotational direction switch
9
On/Off switch
10
Universal bit holder
*
11
Screwdriver bit
*
12
Screwdriver bit with ball catch
*
13
Drill bit with hexagon shank
*
14
Drill bit with SDS-PLUS tool holder
*
15
Handle (insulated gripping surface)
16
Socket for charge connector
17
Charge connector
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of
accessories can be found in our accessories program.
3.3 Electrical connection (Fig. D)
Battery Charge-control Indication
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature of 70 °C is exceeded, the
electronic control switches off the power tool until the
temperature is in the optimum temperature range again.
Additionally, the battery charge-control indicator
5
flashes
green and red at the same time until the On/Off switch
9
is
released.
3.4 Illustrated description
4. Operating instructions
4.1 Placement and testing
Setting the Operating Mode
With the selector switch for drilling/hammer drilling
4
, the
operating mode of the machine is selected.
Change the operating mode only when the
machine is switched off! Otherwise, the machine
can be damaged.
ENGLISH
LED
Capacity
Continuous lighting, green
Displayed when the battery is
charged.
Displayed when the battery is being
charged.
Continuous lighting, red
6
6
