background image

 

15

 

AUDIO/VISUAL STATUS INDICATIONS

 

The lift is equipped with a chassis mounted 3

-

color LED display light to indicate the operating condi-

tion of the lift.  Accompanying this is an audible alarm that will sound accordingly.

 

 

STATUS LIGHT

 

AUDIBLE ALARM

 

CONDITION

 

RED

-

YELLOW

-

GREEN

 

1 Second beep

 

Power

-

up Cycle

 

 

 

 

SOLID GREEN

 

None

 

Ready to Operate

 

 

 

 

 

 

 

YELLOW BLINK

 

1/4 Second beep

 

(30 Seconds)

 

 Batteries are not being charged 

 

(Beeping repeats every 10 minutes )

 

 

 

 

 

 

 

YELLOW PULSE

 

1/2 Second beep

 

(5 Minutes)

 

Low Battery Voltage (under 22.5 volts)

 

 

 

 

2 YELLOW FLASHES

 

1/2 Second beep

 

Seat Swivel Latch Sensor

 

3 YELLOW FLASHES

 

1/2 Second beep

 

Footrest Obstruction Sensor

 

 

 

 

2 RED FLASHES*

 

3 Second beep

 

Sensor Fault (2 or more sensors engaged)

 

3 RED FLASHES*

 

3 Second beep

 

Final Limit

 

4 RED FLASHES*

 

3 Second beep

 

Travel Timeout (Motor running for more than 2

-

1/2 

minutes)

 

5 RED FLASHES*

 

 

Overspeed Governor Set

 

 

 

 

YELLOW SOLID

 

(30 SECONDS)

 

1/2 Second beep

 

(30 Seconds)

 

Overload (Over 22 amps for 3 seconds)

 

 

 

 

RED SOLID

 

(3 SECONDS)

 

3 Second beep

 

Key turned off while traveling( Optional)

 

 

 

 

OFF (SLEEP)*

 

None

 

Very Low Battery Voltage (Under 20.5 Volts for  5 
minutes)

 

 

 

 

FLASH = 2 per second

 

 

 

BLINK = 1 per second

 

 

 

PULSE = 1 per 10 seconds

 

 

 

*Requires power to be cycled OFF/ON.

 

 

Summary of Contents for SL19

















Reviews: