background image

First Time Use 

11.0 

Dealer Assistance                                                                     11.1 

During first time use by the client, it is advised that the dealer or service               
technician assists and explains the configuration to the customer (the user  
and/or the attendant). If needed, the dealer can make final adjustments.

 

User Testing                                                                            11.2 

It is important that the customer is fully aware of the installation and how the 
headrest can be adjusted in order to gain the best positioning possible. As a 
dealer, proceed as follows: 

 

Explain and show the customer how you have executed the installation, and explain        
the function. 

 

Have the user test the position of the GAT444-IP hardware: 

 

Is the hardware in the proper position for the client? 

 

Can the user safely operate the chair? 

 

Is the placement of the GAT444-IP in an optimal position for the user? 

 

If needed, adjust the hardware to the proper position. 

Explain to the customer any possible issues and how to address them. 

 

Conditions of Use                                                                    11.3 

The Gatlin Swivel Table is intended for use as installed by the dealer, in                 
accordance to the installation instructions in this manual: 

 

The foreseen conditions of use are communicated by the dealer or service technician to 
the user and/or attendant during the first time use. 

 

If the conditions of use change significantly, please contact your dealer or a qualified                     
service technician to avoid excessive wear and tear or unintended damage. 

 WARNING 

The Gatlin Swivel Table should only be prescribed and fitted by qualified health 
care professionals. 

Summary of Contents for GAT444-IP





















Reviews: