background image

10

DESCRIPTION / REASON

SERVICE

INTERVAL

ITEM

Daily

Daily

Monthly

Prior to

storing 

MAINTENANCE

Weekly

Through normal operation of your air compressor, condensation of water 

will accumulate in the tank. To prevent corrosion of the tank from the inside, 

condensation must be drained at the end of every workday. Be sure to wear 

protective goggles. Relieve the air pressure in the system then open the 

drain valve on the bottom of the tank to drain. Under cold conditions it is 

especially important to drain the tank after each use to reduce the chance 

of problems resulting from the freezing of condensation water.
NOTE: Refer to instructions on how to drain tank (page 10).
Pull the safety valve daily to ensure that it is operating properly and to clear 

the valve of any possible obstructions.
Check that all connections are tight. Small leaks in the tank, 

hoses,connections or transfer tubes will substantially reduce the air 

compressor and tool performance. Spray a small amount of soapy water 

around the area of suspected leaks with a spray bottle. If bubbles appear, 

repair, replace or reseal the faulty component. Do not over-tighten any 

connections.
A dirty air filter will reduce air compressor performance and life. To avoid 

contaminating the pump, the filter should be cleaned frequently and 

replaced on a regular basis. Clean the cartridge filter by blowing on it with a 

blow gun (page 10).
Before storing the air compressor:

• Drain tank (page 10).

• Use an air blow gun to clean all dust and debris from the compressor.

• Disconnect and wind up the power cord.

• Clean the ventilation openings on the motor enclosure with a damp cloth.

• Drain all moisture from the tank.

• Pull the pressure safety valve to release all pressure from the tank.

• WARNING:Storage covers could cause a fire resulting in death or serious injury.

• Store the air compressor in a clean and dry location.

• In cold weather, store the compressor in a warm building when it is not in use.

This will reduce problems related to starting the motor and the freezing of water 

condensation.

-Do not place a storage cover over a hot air compressor.

-Let equipment cool for a sufficient time before placing the cover on the 

equipment.

Drain the tank

Check the valve

Test for leaks

Clean the air

filter

Storage

Check Safety Valve

Before starting the compressor, pull the ring on the safety valve to make sure that the safety valve operates 

freely. If the valve is stuck or does not operate smoothly, contact a trained service technician.

How To Drain Tank

1. Set the ON/OFF switch to the O (OFF) position.

2. Unplug the power cord.

3. Turn air pressure regulator knob counter-clockwise to set the outlet pressure to zero.

4. Pull and hold ring on safety valve, allowing air to bleed from the tank until air pressure is minimized.

5. Place suitable container under unit to catch water.

6. Slightly tilt unit and turn drain valve counter-clockwise to open.

7. After the water has been drained,close the drain valve(clockwise). The air compressor can now be stored.

How to Clean The Air Filter

A dirty filter will reduce the unit s performance and life. To avoid any contamination inside the 

pump, the filter should be cleaned weekly and replaced on a regular basis. The cartridge filter 

should be cleaned with blow gun.

Summary of Contents for 3331081
















Reviews: