background image

Page 9 of 19 

OPERATIONS 

 

 
 

How this machine works: 

 
This appliance works by vaporising an 
environmentally friendly detergent, which is 
based on sugar beet. The effect is that 
chewing gum is broken down into a foam, 
which can be swept away or washed away if 
desired. 
 
A 90ml (3oz) concentrated chemical is diluted 
with clean water to make it 3 Litres (.79 
gallons) of gum removal solution in the internal 
reservoir of the appliance. 
 
The gum removal solution as supplied by 
Steam E Limited is the only approved 
chemical to be used with the Steam-e 
appliance. Using any other chemical, not 
approved by Steam E Limited will invalidate 
the warranty and will likely cause damage to 
the internal components of this appliance. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Lithium Ion Battery: 

 
This machine is manufactured with 33V 18Ah 
rechargeable lithium battery. The charging 
voltage is 100 

– 240V. 

 
The battery should be sufficiently charged 
before each use. The machine is supplied with 
a mains charger that has an LED charging 
indicator light. When the battery is charging 
the light on the charger will be solid red. When 
the battery is fully charged the light on the 
charger will turn solid green. 
 

Note:

 When the machine is being charged the 

battery LED on the top of the machine will be 
solid red.  
 
The battery can be charged either by: 
 

Connecting the battery directly to the 
charger. 

Connecting the charger to the charging 
port while the battery is installed in the 
machine. 

 
The battery will take five hours to fully charge, 
however the battery will reach 80% charge 
within three hours. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 

 

 

Summary of Contents for Gum Remover




















Reviews: