background image

PRE-INSTALLATION

 1. 

Verify correct model has been sized for the cubic feet and type of steam room using the 

GENERATOR SIZING 

GUIDE on Page 3

.

 2. 

Check that the electrical power supply available is adequate for the voltage, amps and phase of the generator

  

warning

ELECTRICAL SHOCK HAZARD

 

 
3. 

All installations and service must be performed by a qualifi ed electrician and/or plumber and conform to all local 
and national codes.  The generator must be installed and operated according to the instructions.  Failure to do 
so will void the warranty and could lead to injury or death due to the live electrical components involved with 
installation.

 4. 

Physical size of the unit and accessibility for plumbing service and Water Level Sensor Probe maintenance must 
be considered.

INSTALLATION, OPERATION & MAINTENANCE MANUAL

SAFETY INFORMATION

 

Prolonged exposure to steam may cause hyperthermia.  Hyperthermia occurs when the internal temperature 
of the body reaches a level several degrees above the normal body temperature of 98.6°F.  The symptoms of 
hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness and 
fainting.

 2. 

The effects of hyperthermia include:  Failure to perceive heat; failure to recognize the need to exit the steam 
room; unawareness of impending risk; fetal damage in pregnant women; physical inability to exit the steam 
room; and unconsciousness.

 3. 

The use of alcohol, drugs, or medication can greatly increase the risk of hyperthermia.

 4. 

Some aroma therapy oils may cause an allergic reaction - USE WITH CAUTION.

 5. 

Children under the age of 16 should not use the steam room without an adult.

 6. 

The steam head, steam line, plumbing and other components become hot during operation.  The steam head 
and plumbing must be installed in a location so that it cannot come into contact with users to prevent burning or 
scalding.  Insulate plumbing lines for additional protection.

 7. 

After the system is shut down the components will remain hot.  Do not come into contact with the steam head or 
components until the system has returned to a normal temperature.

warning

Spa Kur Therapy

Development

Inc

H-e-a-t Spa Kur Therapy Development Inc — www.h-e-a-t.com

5/20

Summary of Contents for SW-10-3BD





















Reviews: