background image

OWNER’S MANUAL

10

Limited Warranty(cant’d)

THIS WARRANTY DOES NOT COVER:

Merchandise sold as reconditioned, used as rental equipment, or floor or display models.
Merchandise that has become damaged or inoperative because of ordinary wear, misuse, cold,
heat, rain, excessive humidity, freeze damage, use of improper chemicals, negligence,
accident, failure to operate the product in accordance with the instructions provided in the
Owner’s Manual(s) supplied with the product, improper maintenance, the use of accessories
or attachments not recommended by All-Power America, or unauthorized repair or
alterations.
Repair and transportation costs of merchandise determined not to be defective. Costs
associated with assembly, required oil, adjustments or other installation and start-up costs.
Expendable parts or accessories supplied with the product which are expected to become
inoperative or unusable after a reasonable period of use.
Merchandise sold by All-Power America which has been manufactured by and identified as
the product of another company, such as gasoline engines. The product manufacturer's
Warranty, if any, will apply.
ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR
EXPENSE

THAT

MAY

RESULT

FROM

ANY

DEFECTS,

FAILURE

OR

MALFUNCTION OF THE PRODUCT IS NOT COVERED BY THIS WARRANTY. Some
states do not allow the exclusion, so it may not apply to you.
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF
ORIGINAL PURCHASE. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply.

All-Power America Inc.

730 S.Epperson Drive

City Of Industry,CA91748

www.allpoweramerica.com

All rights reserve

Summary of Contents for SP-PT235












Reviews: