background image

2

WARRANTY

•  This covers faulty product for 1 year. Check www.stein.co.nz for full details of 

warranty.

•  Any breakage on site will not be covered.

•  The installation must conform to the instructions for the warranty to apply.

HEALTH & SAFETY

•  Glass is heavy and requires two people to handle in most applications.

•  Always stand glass up after unpacking the components and use soft packing when 

in contact with hard surfaces. Take care not to strike an edge or corner on a hard 
surface.

•  All glass is toughened and cannot be reworked or drilled.

•  Wear protective gloves and eye protection.

•  Special care should be taken when drilling walls to avoid hidden pipes or electrical 

cables.

IMPORTANT PREPARATION STEPS!

1. 

Solid fixing must be provided in the walls behind the wall channels. 20mm centre 

off outside of the Acrylic tray.

2. 

Plumbing fittings in the wall need suitable solid fixings.

3.  All plumbing must be completed by a registered plumber and be in place prior to 

being lined.

4.  The wall lining must be a “Wet Area” grade to meet the Building Code.

5. 

The floor must be level and flat without deflection. Walls must be plumb and 
surfaces flat.

6. 

The Acrylic Tray and Liner comes with its own specific instructions. 

TOOLS REQUIRED

 (NOT SUPPLIED)

VIDA SHOWER UNIT SQUARE

WE RECOMMEND A TRADESMAN FAMILIAR WITH THIS TYPE OF INSTALLATION

MATERIALS REQUIRED

 (NOT SUPPLIED)

•  Rags and suitable cleaning materials

• 

Sika Silaflex NG Translucent

Summary of Contents for VIDA








Reviews: